Bathroom worktops and vanity tops in Malden Rushett

Yes. Malden Rushett is on the patch, and the postcodes we work here are KT9. It is worked on our south west London run, along with the rest of Kingston upon Thames. Overhanging branches clear the roof of a car and catch the roof of a van, so the drive is looked at from the driver seat rather than from the doorstep. A vanity fit is a short visit with one or two pieces in it, so the van stands only for as long as it takes to walk them in. We arrive with the offcut pieces already labelled by room. We template in your kitchen and fit in your kitchen, so there is nothing to visit and nothing to collect.

The chimney breast has almost always been taken out of the kitchen with the stack left standing above it, so that bay of wall is newer plasterwork on a different plane. The bathroom in one of these is almost never original: it is a later room over the back addition, or a bedroom divided in two. Stud partitions want noggins before a wall-hung unit goes up. Where the sill lands inside the height an upstand would occupy there is no upstand, and the stone either dies into the reveal or stops short of it. Bathrooms carry the same problems in a smaller room, and a smaller room leaves a vanity nowhere to absorb them. A sloping floor is corrected under the unit, not under the stone.

A side gate and a back door mean the stone never goes through the house at all, which keeps the dust and most of the risk outside. A vanity is the one piece of stone that route will not usually defeat, because a top cut to a standard unit depth weighs what one person can manage. A vanity top is lifted once and set down once. On a drive that only takes one vehicle nose-in, the van has to reverse the whole length of it to get back out, which decides which way it goes in. A bathroom booked on its own rarely fills a day, so it can be put into whichever part of the day the street is easiest. An en-suite and a family bathroom come off the same load.

Not to any real extent, and it would be easy to imply it was. What the research on this patch actually lists is worktop templating, worktop installation and worktop design & quotation. It describes the kitchens on this patch, not the work that goes into them. Same quoting, same cutting, same fitting as anywhere else on the patch. The junction between the original room and the extension is the point to watch, because the two floors rarely sit at the same height. Work of that kind brings en-suites with it, and an en-suite vanity is a smaller piece again carrying exactly the same four operations. The bathroom schedule follows the plumber, not the programme. Extension kitchens are usually specified long before they are buildable, so the run lengths on the drawing and the run lengths in the room are different numbers. Where several bathrooms are done in one building the tops come off one slab run, because two greys from two batches sit badly on adjoining floors. A building turned over floor by floor needs the batch held.

Power and waste come up through the floor, and where they surface decides which cabinet can hold a sink and which one cannot. That shape decides what is left on the slab when the kitchen has been cut, and what is left on the slab is where most vanity tops come from. One template visit covers both rooms if both are ready. Material is £110-£550 per square metre supply only, and templating, fabrication and fitting are quoted on their own lines.

Casement handles and stays swing down into the space above the worktop, so the clearance that counts is the one measured with the window open. A vanity has no depth to lose, so where a kitchen run would take a ten millimetre scribe without noticing, a shallow top cannot spare it. The tap has to clear the reveal before the hole is drilled. Have the vanity unit fixed and levelled, and the basin and tap on site, before the templater arrives, and tell us what is inside any boxing. A street with houses in single occupation next to the same houses cut into flats produces two completely different jobs from the same elevation. Who is paying decides the material here more than anywhere else, because a vanity is small enough that an expensive stone stops being an expensive decision. An en-suite in a let flat is specified like the bathroom next door.

Dark and heavily veined stone shows a join more than a pale even one, which is worth knowing before the slab is picked. Join count and position are settled from the template drawing rather than improvised on the fitting day. There are only ever a few legal positions, and the one taken is furthest from the light. A hob cut-out and the floor penetration feeding it have to land over the same cabinet, and where they do not it is the stone that gets redrawn rather than the pipework. A bathroom ordered with the kitchen is taken from the same slab run, so the two rooms match rather than nearly match. The vanity comes off what the kitchen leaves behind.

The bead where the sink and hob meet the stone is siliconed rather than sealed, and wants watching. Granite tells you when the seal wants topping up: water stops beading on the surface and starts darkening it instead. A seal is not waterproofing. It only buys time to wipe a spill up. Ceilings are high in these, so wall unit heights and splashback heights are open choices rather than things the room has already decided. Either way the walls are thin, the floor is boards over shallow joists and nothing meets at a right angle, so the vanity is scribed at both ends and the unit is fixed back to the wall as well as standing on the floor. A bathroom over a kitchen has its waste run already decided.

Machining is permanent. If a later kitchen moves the sink, the grooves stay where they were cut. Grooves and an undermounted bowl are usually specified together, since the grooves are run to the bowl edge. Grooves are machined in the workshop at the same time as the bowl cut-out, because they cannot be done well in a kitchen. A hundred and forty years of alterations sit under the current kitchen, and the worktop is what has to sit flat on top of all of it. What that does to a vanity is push the whole job into a narrow depth, because a bathroom takes the same stone as a kitchen in about two thirds of the width. Nothing about a vanity is standard except the depth of the unit.

An upstand covers the gap where the worktop meets a wall that is not flat, which is its real job. The joint between splashback and worktop is siliconed, never grouted, so it can move a little without cracking. If it is a decision for later, say so at the template: the match is a question about the batch. The bay at the front and the back addition at the rear were built to different standards, and the kitchen is nearly always in the weaker of the two. The bathroom in one of these is usually a later addition over the back kitchen, so the walls are thinner, the floor moves and a vanity has to sit level in a room that is not. High ceilings do nothing for a vanity, but the reveals do.