Stone bar tops in Woodford Bridge

Yes. Woodford Bridge is on the patch, and the postcodes we work here are IG8. It is worked on our east London run, along with the rest of Redbridge. Block paving bedded on sand can rut under a fully loaded van, and that is said to the customer beforehand rather than explained afterwards. A bar fit runs longer than a worktop run, because the frame, the support and the stone are three stages and only the last of them is quick. The offcut from a bar sink leaves in the van. Both visits happen in your kitchen, the template and the fit, so there is nothing to visit and nothing to collect.

A two-up two-down has a kitchen that was never designed to be one, so the run is short, the ceiling is low and every millimetre of depth gets argued over. A bar in one of these houses is either the end of a through-lounge or a cellar conversion, and the two behave differently. The riser gets notched around, not built away from. A scribe has a working limit, and past twenty millimetres or so the back edge starts eating depth the run cannot spare. A bar top is levelled to itself rather than to what it stands on, so the packing goes into the frame and the stools take up whatever the floor is doing. The support plan is drawn at the same time as the cut-out.

A front path with a gate and a turn or two adds handling before the door is even reached, and every handling movement is another chance to catch a corner. That matters more on a bar than on a run, because a join forced by the way in cannot be allowed to land in the unsupported part of the nose. A polished front edge is protected from the tail lift to the frame. Where the drive is shared, the half-hour the van spends in the way is agreed with the neighbour in advance rather than apologised for at the time. That has to cover more than the unload, since the corbels, the flat bar and the fixings all come off the van well before the top does. A suspension is booked for the fitting day, not the delivery hour.

Honestly, no, though it would be easy to claim otherwise. What the research on this patch actually lists is worktop replacement, worktop installation and worktop templating. That says something about the housing round here, not about the work. Quote, cut and fit are the same here as on any other part of the patch. An open-plan extension puts the worktop in the middle of the living space, so it is looked at from the sofa as well as worked on. A bar is nearly always the last thing added to a project, so it is templated on a visit of its own once the joinery around it has stopped moving. The evening use is what the piece is sized for. Extension budgets are usually well spent by the time the worktop is ordered, which is where the choice between quartz and a thinner sintered stone actually gets made. Harder use and stronger cleaning products push the answer towards porcelain or sintered stone, because a resin-bound surface is the one that shows what has been left standing on it. Bars are quoted as their own item, never as extra metreage.

Where a run finishes hard against a wall the last few millimetres are scribed, and where it finishes in open floor it is cut square and polished, which is two different jobs on one length. A bar laid over that is a second level rather than a wider one, so it wants a spine underneath it and a settled detail where the two heights meet. The bar length answers to the seats, not to the wall behind it. Expect £110 to £550 per square metre for material supply only, with templating, fabrication and fitting on their own lines.

Walls that bow along their length are the normal condition rather than the exception, and a straight-cut back edge will show a shadow gap at one end and touch at the other. Where the nose has to be carried past something fixed the support moves rather than the stone, since a corbel landing in the knee space is worse than no corbel at all. A bar top will not correct a frame that is out of true. Send the length you want, the number of stools, and photographs walking from the pavement through to the room, including the cellar stair if the bar is going down there. The same building type can arrive as a careful one-off kitchen or as a fast turnaround, and the honest answer is that they are priced differently. A home bar is discretionary work, so the edge profile, the corbel detail and the radius on the nose are worth settling properly rather than defaulting to whatever is quickest. Consent for a structural fixing comes before the fitting date.

What decides it is not the width of the stairwell but the length of piece that can be turned in it. An external stair, a side return or a rear garden counts as carry and is measured the same way. Where there is a lift, whether it can be booked out and padded matters as much as its size. A carpeted hall runs a trolley badly, so a heavy piece is carried rather than rolled from the threshold in. The steel and the corbels travel that same route and go in first, so a bar is three separate carries into one room rather than a single delivery. Nothing is leaned on a stud wall while it waits to be fitted.

A boiling tap needs a hole of its own and a cupboard below for the tank, so the units change too. Two bowls means two cut-outs and a bridge of stone between them, which decides where the sink can go. If the sink or hob changes after the template, the drawing changes first and nothing is cut meanwhile. A doorway partway along one wall breaks that side into two separate pieces, and two short pieces cost more between them than the single long one they replace. Where the counter runs flush with the working surface instead of standing above it the whole thing becomes one plane, which looks better and doubles the unsupported span. A deep apron takes knee room away quietly.

Stone does not flex, so a run that rocks on its carcasses rocks just as badly once it is stone. Variation past what packing can take up has to be corrected in the carcasses before we cut, because the template records the units as they stand. Packing takes up small variation. It is not there to hide something that belongs in the units. A run can measure dead right at both ends and still belly out in the middle, which only appears once the template plots the intermediate points. Anything that puts a notch in a bar takes material out of the piece at the point people lean on it, so the notch and the support are drawn together or not at all. Fixings go into timber that was put there for them.

Tiling bonded to the wall behind usually comes away with the old top, so that wall is agreed beforehand. Taking the old tops off and disposing of them is its own line on the quote rather than something folded into the stone price. Old laminate is light and awkward rather than heavy, so it is usually the easier half of the day. A step up from the drive to the threshold turns the last two metres into a lift, and a lift is where two pairs of hands become the minimum. A trade bar is fitted around opening times, so the window the van has and the window the room has are rarely the same window. Bar tops are set once, so the day is planned to allow it.