Reception counters and desks in Biggin Hill

Yes. Biggin Hill is on the patch, and the postcodes we work here are TN16. It is worked on our south east London run, along with the rest of Bromley. Some drives are wide enough for the van and too short for the tail lift, because the tail lift needs its own clear metre behind the vehicle. A commercial frontage rarely has anywhere to stop, so the unload is timed rather than assumed and the counter pieces come off first. Whoever holds the lease usually holds the loading bay. We template in your kitchen and fit in your kitchen, so there is nothing to visit and nothing to collect.

The floor is a solid slab with a screed over it, which is stable underfoot and rarely flat across a long run. Practices in this stock are usually converted houses on or behind an interwar parade: a dental surgery, a veterinary practice or a small office with its reception in what was the front room. A pharmacy counter is two heights before anybody draws it. A room can be out of square in both directions at once, so the wall that leans is also the wall that runs downhill, and one scribe cannot answer both. A counter is worse off than a kitchen here, because it usually stands clear of the wall and has nothing behind it to hide a gap. A lobby floor that falls is packed out under the joinery.

A short hard approach with no steps means a full-length piece can be walked in flat by two people rather than turned up on edge. A counter top is one long piece with no run of cabinets to break it, so the route decides the join count before the sightlines get a vote. The counter waits on the van until there is somewhere to stand it. Where the drive falls away from the house the trolley wants to run, and where it climbs the same load has to be pushed the whole way up. Loading bays belonging to the building are booked by whoever holds the lease, and that is seldom whoever ordered the counter. The longest counter piece decides the swing radius outside.

Not really, and there is no sense dressing it up. What the research on this patch actually lists is worktop templating, worktop installation and worktop replacement. That is a statement about the local housing rather than about the work. It gets quoted, cut and fitted exactly as it would anywhere else on the patch. Extension kitchens are usually specified long before they are buildable, so the run lengths on the drawing and the run lengths in the room are different numbers. Counters are nearly always one-offs, so the saving that comes from repeating a specification is not usually on the table here. Matching across sites means matching blocks, not matching names. Extension work runs late far more often than it runs early, and the worktop is close to the last thing in, so the date agreed at the start is rarely the date that happens. Where an operator is fitting out several receptions, the counters come off one slab run so the desks read as a set rather than as neighbours. The counter is quoted with the programme written beside it.

The offcut taken out of the middle for a hob is a large usable piece, and it is worth deciding early whether it becomes an upstand or goes in the skip. A counter has the same argument in miniature: a straight run nests kindly on a slab, and every return costs yield. The public side and the staff side take different details. Stone is £110 to £550 per square metre supply only, and the templating, the fabrication and the fitting each carry their own line.

Plaster thickness varies over the height of a wall, so the line at worktop height is not the line at skirting level, and the units decide which one matters. What a counter is scribed to is the joiner's carcass rather than the plaster, which is why it is templated after the carcass is fixed and never before. Nothing on a counter is corrected with sealant. Confirm whether the reception is at ground level or up the stair, and send the carcass drawing with the chimney breast and any bay recorded on it. Where two people share the decision it helps to know early which of them is settling the edge profile and which is settling the budget, because it is rarely the same person for both. The same split runs through commercial property: a landlord fitting out a shell and a tenant fitting out their own reception want different things from one counter. A desk in a re-let space is specified for the next occupier too.

The alternative stands on the surface, so the choice is losing worktop permanently or only while you are draining. Grooves are machined into the surface rather than applied to it, so there is nothing to come loose later. Grooves are machined in the workshop at the same time as the bowl cut-out, because they cannot be done well in a kitchen. The original plan put a larder and a back door on the same wall, and both leave awkward stubs once the room is opened up. A reception counter answers to the building it stands in more than to the drawing, because it is fabricated to a carcass somebody else has already built and fixed. The counter is drawn to the carcass, and the carcass is measured first.

Where a top takes wine, oil and lemon most days, the non-porous materials ask least of the household. No maintenance visit is built into the job. Soap, water, and on the porous stones a seal. Topping a seal up is a wipe-on job with a cloth. These were built with generous circulation, so an island or a peninsula fits in a room that would be too tight in a house of the same floor area. The carcass is built around a chimney breast or into a bay, so the counter is drawn to a shape the joiner had to invent rather than to a rectangle, and the return between the upper counter and the transaction shelf rarely nests neatly against the long piece. Marketing suites get a permanent counter for a temporary lobby.

Splitting a run costs a join, and that is the price of getting stone into the room at all. The alternative to a join is a shorter run, which is usually the wrong thing to trade away. A join added to get stone into the room is a different thing from a join added because the slab ran out, and the quote says which is which. Where the van stands level with the front of the house a piece gets handled twice instead of five times, and stone breaks on handling rather than on the road. The lower transaction shelf is short and easily handled; it is the upper counter that has to be walked in on edge and turned at every corner. Two heights means two carries, and the low one is not the difficult one.

Stone cannot be filled and made good the way laminate can, so a damaged piece is remade rather than patched. A remake goes back through the same cutting and polishing, so it is a return visit rather than a patch. The workmanship guarantee runs 5 years on every kitchen we fit. Even an easy kerbside carry wants the pavement clear at the tail lift, because a three-metre piece on edge has a swing radius nobody expects until it is swinging. A lobby is one of the few places a piece can be staged, so the counter comes in early and stands on trestles until the carcass is ready for it. Protection stays down until the last piece is bedded.