Restaurant and cafe table tops in Oakleigh Park

Yes. Oakleigh Park is on the patch, and the postcodes we work here are N20. It is worked on our north London run, along with the rest of Barnet. A front drive is the best thing that can happen to a fitting day, because the tail lift comes down within a few metres of the door and nothing is on a clock. A table order comes off the van as a stack of frames and a pallet of bases, and both of those need somewhere to stand before either is moved. Deliveries land before the doors open wherever possible. Your part of it happens entirely at home, with nothing to travel to and nothing to bring back.

These were built late enough to have a damp course and proper footings, so the front of the house is close to true and the rear addition holding the kitchen is the part that has dropped. The trade on streets like these sits in a parade of narrow shopfronts, so the dining room is long and thin and the covers are won by the width of the gangway rather than by the size of the room. Terraces and gardens live outdoors all year. Once the carcasses are levelled the gap under the plinth varies along the run, and that varying gap is the honest record of what the floor is doing. None of that is scribed against on a table, since it stands clear of every wall, so the awkwardness moves from the back edge to the floor and the base. The base carries the weight and the floor carries the base.

Two people will walk a two-metre piece in through a front door; the same hall with a three-metre piece wants four, purely because nobody can let go halfway. A table order is many small pieces rather than one long one, so the route decides how many trips the delivery takes rather than how big anything can be. Handling is where a polished edge gets damaged. Off-street parking means the van stays put all day, so tools, packers and the offcut we would rather have than not are all within reach. The bases are the heavy half of the delivery, so the pallet is dealt with first while there are still hands free for it. The plan on the van matches the plan on the floor.

No, not particularly, and it would be easy to say otherwise. What the research on this patch actually lists is worktop installation, worktop templating and worktop design & quotation. That is the local housing talking rather than anything about the job. It is priced, cut and fitted no differently here than anywhere else we cover. The junction between the original room and the extension is the point to watch, because the two floors rarely sit at the same height. Table work arrives as a batch by its nature, and a batch means one slab run rather than the same colour ordered twice a year apart. The programme decides the delivery, not the workshop. Extension kitchens are usually specified long before they are buildable, so the run lengths on the drawing and the run lengths in the room are different numbers. A room opening in a second phase is worth naming now, while the material is still on the ground and a match is a telephone call. Sizes are frozen before machining rather than during it.

Where the sink and the hob face each other across the aisle, everything carried between them crosses the walkway, and that is the one movement the shape cannot design out. What decides the cut list here is the seating plan rather than the room shape, and one repeated table size nests far better than six one-offs. Colour is matched across the room, not table by table. The supply-only figure for material runs £110 to £550 per square metre, and templating, fabrication and fitting are lines of their own.

A wall line that runs level over a floor that does not means the finish closes up on the plinth at one end, which is joinery rather than something the stone can answer. A column, a boxed duct or a fixed bench in a dining room is designed around with a shape cut to suit rather than notched on site. A shallow room decides the diameter early. Send the seating plan with the gangway widths marked, and bring in one of the bases or the maker’s drawing so the bolt centres can be measured properly. Some doors in a building need a consent letter and some need nothing at all, so the first question is which arrangement applies here rather than which one is usual. A table top bolted to a base you already own is loose furniture rather than a fixture, so it leaves with the operator at the end of a term. The drawing goes to whoever has to approve it.

Plumbing, gas and electrical work are not in the figure, because we do not do them. Material is quoted supply only and templating, fabrication and fitting sit on their own lines, so it is visible which part is stone and which is labour. What moves the figure after templating is a change you make: a different edge, an extra cut-out, a bigger sink chosen late. Where two pieces meet over a fall in the floor the join has to be flush to the hand as well as true to the level, because the eye reads the join and forgives the room. Where a floor falls away, the levelling is done by winding out the feet under each base rather than by packing anything under the stone. Sharp corners are eased wherever people pass.

Granite is porous to varying degrees, so it is sealed when we fit it and topped up over the life of the worktop. Where a top takes wine, oil and lemon most days, the non-porous materials ask least of the household. Topping a seal up is a wipe-on job with a cloth. The kitchen occupies the ground floor of the addition with a garden door at the far end, so there is a second way in that is narrower than the front door and a great deal shorter. That measurement comes first: once the gangway is fixed the table dimension follows, and on most of these frontages that means a six hundred millimetre square for two and a seven hundred millimetre round where the room widens towards the back. Converted houses mean several sizes, not one.

Take the old tops off yourself if you would rather, and the quote simply carries one line fewer. If you want the old top kept for a garage or a utility, say so and it stays on site. An old stone top is heavier coming out than the new one is going in, and leaves in sections. A drive that shelves towards the house needs the van chocked and the trolley controlled, since a loaded A-frame gathers speed quickly on a slope. Where the standing is short the pieces are counted off at the tail lift against the plan rather than checked once they are already inside. A long push from the kerb is planned, not discovered.

Stone cut to somebody else’s drawing cannot usefully be re-cut to yours. How much slab you hold matters: upstands and any remake have to come out of the same batch. Thickness has to be known before quoting, since it decides the edge, the cut-outs and what the units carry. Extension work runs late far more often than it runs early, and the worktop is close to the last thing in, so the date agreed at the start is rarely the date that happens. Where an operator changes hands the bases usually stay, so a refit becomes a resurface and the saving comes from what is already bolted down. A second site is quoted from the same specification.