Stone bar tops in Parsloes

Yes. Parsloes is on the patch, and the postcodes we work here are RM9. It is worked on our east London run, along with the rest of Barking and Dagenham. Where the van can pull up level with the gate the pieces are handled the fewest times, which is what actually protects them. A bar fit runs longer than a worktop run, because the frame, the support and the stone are three stages and only the last of them is quick. The frame is checked before anything comes off the van. The template happens in your kitchen and so does the fit, so there is nothing to visit and nothing to collect.

Windows and doors were replaced across whole streets on one programme, so the kitchen window is a plastic frame in the old opening with a deep lined reveal. The one advantage here is the fabric: dense blockwork holds a fixing properly, which makes a wall-carried front edge realistic where a stud partition would not allow it at all. A garage floor slopes and the frame takes that up. Where the boxing stands proud of the finished wall the upstand behind it has to be broken into separate lengths, because one piece cannot pass it. A bar top is levelled to itself rather than to what it stands on, so the packing goes into the frame and the stools take up whatever the floor is doing. What the bar wraps around is templated, never assumed square.

Where the garden is level and the back door is wide the pieces get staged outside on trestles and brought in one at a time as the fitters are ready for them. That matters more on a bar than on a run, because a join forced by the way in cannot be allowed to land in the unsupported part of the nose. Nothing about a front edge survives being dragged. Unrestricted does not mean empty, and a street that is clear at seven is usually full by nine. A trade bar is fitted around opening times, so the window the van has and the window the room has are rarely the same window. A red route buys minutes and a bar top needs hours.

Not really, and claiming otherwise would cost nothing and mean nothing. What the research on this patch actually lists is worktop replacement, worktop splashbacks & upstands and worktop installation. It reflects the local housing rather than any difference in the work. It is quoted, cut and fitted here the same way it is anywhere else on the patch. Quartz suits let property well: no sealing, no annual maintenance, and nothing an incoming tenant has to be told to look after. Where the same detail is repeating across several rooms the support gets standardised once and then cut to length, which is cheaper than drawing it each time. What was drawn and what was built are compared at template. A worktop replacement between tenancies is a single-day job by design, because the flat is not earning while it is empty. Harder use and stronger cleaning products push the answer towards porcelain or sintered stone, because a resin-bound surface is the one that shows what has been left standing on it. A bar is templated after the joinery has stopped moving.

The free end is what needs deciding early: square edge, mitred apron down the end, or a full waterfall to the floor, and a waterfall is cut in sequence off the same part of the slab. A bar laid over that is a second level rather than a wider one, so it wants a spine underneath it and a settled detail where the two heights meet. Stools need floor as well as knee room, and both are drawn. Supply-only material is £110 to £550 per square metre, and templating, fabrication and fitting are quoted separately rather than rolled in.

A boxed soil stack or service riser in the corner of a run eats into the worktop depth and has to be scribed around rather than cut square. Where the nose has to be carried past something fixed the support moves rather than the stone, since a corbel landing in the knee space is worse than no corbel at all. The support plan is drawn at the same time as the cut-out. Send a photograph of every corner of the room so we can see the boxings, the length you want, and how many stools you expect to use. A street with houses in single occupation next to the same houses cut into flats produces two completely different jobs from the same elevation. A home bar is discretionary work, so the edge profile, the corbel detail and the radius on the nose are worth settling properly rather than defaulting to whatever is quickest. A bar outlasts whoever specified it.

Templating and fitting are two visits, not one, and the gap between them is when the stone is actually cut. The design and quotation visit comes first. It is free and carries no obligation. If the units run late the template moves, not the fit: the gap between them is fabrication. A passive vent or a ducted extract shaft takes a corner of the kitchen from floor to ceiling and cannot be reduced. A bar top put into a room like that is an overhang question first, because the nose has to carry people leaning on it long after the slab has stopped being interesting. A bar top is a structural piece with a polished face on it.

Units have to be fixed down as well as levelled. A loose carcass moves under stone. Variation past what packing can take up has to be corrected in the carcasses before we cut, because the template records the units as they stand. If the carcasses are corrected, the template is taken again, since a drawing off units that then moved is worthless. Boxing is rarely the same depth at worktop height as it is at floor level, so measuring it low down is the usual reason a top will not sit back. Anything that puts a notch in a bar takes material out of the piece at the point people lean on it, so the notch and the support are drawn together or not at all. A bar top will not correct a frame that is out of true.

The bowl position has to be settled before templating, since the grooves are set out from it. The grooves sit inside the depth of the top with stone left either side, so a shallow run limits them. Machining is permanent. If a later kitchen moves the sink, the grooves stay where they were cut. Windows sit in deep concrete reveals with a cast sill, and that reveal is usually the least square thing in the room. None of that stops a bar being fitted level, but it does mean the top is set to a datum of its own and packed off the frame rather than followed down to the floor. People push against the front edge, so the front edge gets the steel.

Where there is a lift, whether it can be booked out and padded matters as much as its size. Hoisting through a window is occasionally the answer, and it is a decision made at the template, not improvised on the fitting day. The alternative to a join is a shorter run, which is usually the wrong thing to trade away. Grass and gravel will not take a loaded trolley, so a boarded track gets laid from the gate to the door before the first piece moves. The steel and the corbels travel that same route and go in first, so a bar is three separate carries into one room rather than a single delivery. The corbels go in before the top does, and both use the same door.