Stone bar tops in Well Hall

Yes. Well Hall is on the patch, and the postcodes we work here are SE9. It is worked on our south east London run, along with the rest of Greenwich. Unrestricted kerbside is straightforward as long as the space in front of the property is actually clear when the van arrives. A bar fit runs longer than a worktop run, because the frame, the support and the stone are three stages and only the last of them is quick. Steel and corbels are unloaded before the stone is. Your part of it happens entirely at home, with nothing to travel to and nothing to bring back.

An inter-war terrace is wider than a Victorian one and shallower than a semi, so the kitchen is a compact square room rather than a galley. These bars nearly always land at the open end of a knocked-through kitchen and dining room, which means the piece is read from both sides and both sides get the same edge treatment rather than one being left as a cut face. Noggins first, brackets second, stone last. Sill height gets settled with the template on site, because it is one of the few dimensions nobody has measured before we arrive. On a bar that counts twice over, because the same obstruction has to be cleared by the stone above it and by the knees of whoever is sitting at it. Nothing under the nose is allowed to be in the way.

Suction lifters need a clean dry face to hold, so in the wet the pads come off and the piece goes back to being carried on webbing by hand. That matters more on a bar than on a run, because a join forced by the way in cannot be allowed to land in the unsupported part of the nose. A polished front edge is protected from the tail lift to the frame. On a street with no restrictions the constraint is other residents rather than a warden, so it is worth putting a cone or a car out early. A trade bar is fitted around opening times, so the window the van has and the window the room has are rarely the same window. The bar top waits on the van until the frame is level.

No, not particularly, and it would be easy to say otherwise. What the research on this patch actually lists is worktop templating, worktop fabrication and worktop replacement. That is the local housing talking rather than anything about the job. It is priced, cut and fitted no differently here than anywhere else we cover. The junction between the original room and the extension is the point to watch, because the two floors rarely sit at the same height. A bar is nearly always the last thing added to a project, so it is templated on a visit of its own once the joinery around it has stopped moving. A bar in constant use is a maintenance decision as well. Extension kitchens are usually specified long before they are buildable, so the run lengths on the drawing and the run lengths in the room are different numbers. Harder use and stronger cleaning products push the answer towards porcelain or sintered stone, because a resin-bound surface is the one that shows what has been left standing on it. One detail across several rooms keeps the fixings the same.

A dishwasher door on one side and an oven door on the other cannot both stand open in a narrow aisle, so which appliance goes where matters more in this shape than in any other. A bar laid over that is a second level rather than a wider one, so it wants a spine underneath it and a settled detail where the two heights meet. Stools need floor as well as knee room, and both are drawn. The material band is £110 to £550 per square metre supply only, and templating, fabrication and fitting are quoted on their own lines.

A window board sitting below finished worktop height leaves two choices, drop the top under it or notch the stone around it, and both cost more than a straight run. A bar top is levelled to itself rather than to what it stands on, so the packing goes into the frame and the stools take up whatever the floor is doing. The back of a bar is seen, so the back is finished. Confirm the finished height you want and whether the bar is seen from both sides, and tell us who is building the frame and when it will be complete. Where someone is living in the house through the work, the strip-out and the fit are planned so the kitchen is out of use for a day and not a week. A home bar is discretionary work, so the edge profile, the corbel detail and the radius on the nose are worth settling properly rather than defaulting to whatever is quickest. Seating height is set to a person or to a standard, and stated.

Taking the old tops off and disposing of them is its own line on the quote rather than something folded into the stone price. Old laminate is light and awkward rather than heavy, so it is usually the easier half of the day. Carcasses stay. Surface changes. That is the whole of it. A free-parking street with cars both sides can still leave the van forty metres away, and that distance is carry, not driving. Where the clock is running the frame is levelled and the steel is in before the top ever leaves the tail lift. A licensed room sets the hours and the parking has to agree.

Quartz carries resin, so a hot pan wants a trivet, while granite and sintered stone will take one without complaint. Marble is the one people underestimate. It is porous, like granite, and wants sealing. A seal is not waterproofing. It only buys time to wipe a spill up. There is usually a shared rear alley, and whether the gate onto it is unlocked decides whether long pieces come in from the back. The side passage is usually wide enough for a full length to reach the room, so piece length is decided by the slab and by what the frame will carry rather than by the front door. The riser gets notched around, not built away from.

Packing takes up small variation. It is not there to hide something that belongs in the units. A long top on units that were shimmed once and never checked is the commonest version of this, and it is cheap to fix beforehand. Where a run meets an appliance, level decides whether that appliance door still clears the stone above it. A cill projecting forward of the plaster line pushes the back edge out, and the units then stand off the wall by that amount for the whole length. Where the nose has to be carried past something fixed the support moves rather than the stone, since a corbel landing in the knee space is worse than no corbel at all. Noggins go into a stud wall before a bar is fixed to it.

Most breakages happen on the carry, which is why the route is walked and measured before anything comes off the van. Floors and units are protected before anything comes through the door. A remade piece is cut from the same slab run wherever the slab allows, because a replacement from another batch will not match across a join. A loading bay or a red route puts a clock on the unload, so the pieces come off in the order they will be fitted rather than the order they were loaded. The steel and the corbels travel that same route and go in first, so a bar is three separate carries into one room rather than a single delivery. Nothing is leaned on a stud wall while it waits to be fitted.