Stone bar tops in Whalebone

Yes. Whalebone is on the patch, and the postcodes we work here are RM8. It is worked on our east London run, along with the rest of Barking and Dagenham. A shared drive is only useful if the neighbour is not the one parked behind the van, so we ask which side the standing belongs to before the date is set. A bar fit runs longer than a worktop run, because the frame, the support and the stone are three stages and only the last of them is quick. The offcut from a bar sink leaves in the van. Nothing needs visiting and nothing needs collecting: the template is in your kitchen and so is the fit.

The hot water cylinder sits in a cupboard opening off the kitchen or the landing above it, and the pipework to it drops through the corner of the room. Rooms in this stock are compact, so a bar usually replaces a table rather than sitting alongside one, and it is drawn for two or three stools with enough floor left to get past them. Wide doors make piece length a choice rather than a limit. Walls that bow along their length are the normal condition rather than the exception, and a straight-cut back edge will show a shadow gap at one end and touch at the other. A bar top is levelled to itself rather than to what it stands on, so the packing goes into the frame and the stools take up whatever the floor is doing. What the bar wraps around is templated, never assumed square.

Even an easy kerbside carry wants the pavement clear at the tail lift, because a three-metre piece on edge has a swing radius nobody expects until it is swinging. That matters more on a bar than on a run, because a join forced by the way in cannot be allowed to land in the unsupported part of the nose. The bar top is the last piece in and the first one people touch. Drives with a dropped kerb and a tight turn-in take a long van at an angle, and that angle decides which side the tail lift can work from. That has to cover more than the unload, since the corbels, the flat bar and the fixings all come off the van well before the top does. A suspension is booked for the fitting day, not the delivery hour.

Not really, and there is no sense dressing it up. What the research on this patch actually lists is worktop replacement, worktop installation and worktop templating. That is a statement about the local housing rather than about the work. It gets quoted, cut and fitted exactly as it would anywhere else on the patch. Agents book this work at short notice, because the void only becomes a real date once the outgoing tenant confirms they are going. A bar is nearly always the last thing added to a project, so it is templated on a visit of its own once the joinery around it has stopped moving. What gets leaned on gets specified for leaning. A managed portfolio tends to repeat one specification across every flat, which keeps later repairs and replacements simple to order. Where the same detail is repeating across several rooms the support gets standardised once and then cut to length, which is cheaper than drawing it each time. Batch work still gets its own template per room.

Peninsulas frequently land on a lightweight partition or on units that were never fixed down, and stone needs proper support under it before it goes on. A bar laid over that is a second level rather than a wider one, so it wants a spine underneath it and a settled detail where the two heights meet. The nose line is drawn first and everything works back from it. Material is £110-£550 per square metre supply only, and templating, fabrication and fitting are quoted on their own lines.

A run can measure dead right at both ends and still belly out in the middle, which only appears once the template plots the intermediate points. Where the nose has to be carried past something fixed the support moves rather than the stone, since a corbel landing in the knee space is worse than no corbel at all. The support plan is drawn at the same time as the cut-out. Send a photograph of every corner of the room so we can see the boxings, the length you want, and how many stools you expect to use. Planned programmes run several kitchens in sequence, so template, fabrication and fitting move as a rolling operation and one uncollected key holds up more than one flat. A home bar is discretionary work, so the edge profile, the corbel detail and the radius on the nose are worth settling properly rather than defaulting to whatever is quickest. Who signs off the steel is settled before it is ordered.

On a porous stone the grooved area is sealed with the rest, and it gets wet more than anything else. A groove set needs a clear stretch of worktop beside the bowl, so it competes with the run for length instead of being free surface. The bowl position has to be settled before templating, since the grooves are set out from it. The kitchen doorway is usually offset into a corner, so one leg of an L is short before anyone has designed anything. A bar top put into a room like that is an overhang question first, because the nose has to carry people leaning on it long after the slab has stopped being interesting. A home bar is joinery first and stone second.

Slabs come in finite sizes, so a long run needs a join whatever the room looks like. A join cannot cross a cut-out, so a sink mid-run takes away the position you would have used. A mitred join at a corner is a different job from a butt join along a run, and they are not priced the same. Because a peninsula is seen from both sides, the underside of any overhang gets the same edge treatment as the top, which is easy to leave out of a spec. Where the counter runs flush with the working surface instead of standing above it the whole thing becomes one plane, which looks better and doubles the unsupported span. A radius on a walked-past corner is agreed at drawing stage.

Taking the old tops away is a line rather than an assumption, so it comes off if you do not want it. Nothing is payable until the template, and the template measures the room as it stands rather than estimating from a plan. Ask for the lines rather than the total. One number for a kitchen tells you nothing you can check. Where a corner is a couple of degrees off, a mitre cut to a theoretical ninety degrees opens on the wall side and there is no closing it afterwards. Anything that puts a notch in a bar takes material out of the piece at the point people lean on it, so the notch and the support are drawn together or not at all. A bar top will not correct a frame that is out of true.

A piece is never laid flat across a gap while it is moved, because that is how stone cracks unaided. A remake goes back through the same cutting and polishing, so it is a return visit rather than a patch. The rest of the kitchen still goes in. One damaged piece does not hold up the pieces either side. A level threshold with hard standing outside it is the one arrangement where a full run goes in without a single re-grip. A top with a bonded apron on the front arrives deeper than a worktop and behaves like a beam, so there is no easing it round a turn at all. Piece length is capped by the turn, then the support is drawn to suit.