Stone bar tops in Havering-atte-Bower

Yes. Havering-atte-Bower is on the patch, and the postcodes we work here are RM4. It is worked on our east London run, along with the rest of Havering. Unrestricted does not mean empty, and a street that is clear at seven is usually full by nine. A bar fit runs longer than a worktop run, because the frame, the support and the stone are three stages and only the last of them is quick. A suspension is booked for the fitting day, not the delivery hour. The template happens in your kitchen and so does the fit, so there is nothing to visit and nothing to collect.

A small room puts the sink, hob and tap cut-outs close together on one short length, and the bridge of stone left between them decides whether it can be cut in one piece. In a cellar the headroom fixes the counter height first and everything else works back from it, and the stair down is the tightest part of the route because stone carried downward is harder to control than stone carried up. A trade bar and a home bar are different pieces of work. Where a corner is a couple of degrees off, a mitre cut to a theoretical ninety degrees opens on the wall side and there is no closing it afterwards. On a bar that counts twice over, because the same obstruction has to be cleared by the stone above it and by the knees of whoever is sitting at it. A bar top is set to one datum along its own length.

A hall that widens further in is still only as good as its tightest point, and that point is usually within a metre of the front door. That matters more on a bar than on a run, because a join forced by the way in cannot be allowed to land in the unsupported part of the nose. Stools and back shelving come in after the stone is down. A skip, a delivery lorry or a run of scaffolding takes the frontage the van needed, so the street is worth a look the day before rather than on the morning. That has to cover more than the unload, since the corbels, the flat bar and the fixings all come off the van well before the top does. Bar tops are set once, so the day is planned to allow it.

Not really, and claiming otherwise would cost nothing and mean nothing. What the research on this patch actually lists is worktop templating, worktop design & quotation and worktop fabrication. It reflects the local housing rather than any difference in the work. It is quoted, cut and fitted here the same way it is anywhere else on the patch. Kitchens go in near the end of a conversion, behind the plastering and the flooring, by which point the programme has already absorbed whatever slipped earlier. A bar is nearly always the last thing added to a project, so it is templated on a visit of its own once the joinery around it has stopped moving. The support detail is agreed with whoever builds the frame. Studio and one-bed conversions put the whole kitchen against a single wall, so the job is one run and everything depends on that one length. Harder use and stronger cleaning products push the answer towards porcelain or sintered stone, because a resin-bound surface is the one that shows what has been left standing on it. Repeated bars get one drawing and one steel schedule.

Island units are rarely fixed to anything at first fix, so they get screwed to the floor and levelled against the perimeter run before the stone is measured at all. A bar laid over that is a second level rather than a wider one, so it wants a spine underneath it and a settled detail where the two heights meet. The nose line is drawn first and everything works back from it. Supply-only material is £110 to £550 per square metre, and templating, fabrication and fitting are quoted separately rather than rolled in.

The stone carries the scribe because the wall cannot be persuaded, so back edges are cut oversize and eased in rather than dropped straight down. Where the nose has to be carried past something fixed the support moves rather than the stone, since a corbel landing in the knee space is worse than no corbel at all. The frame is made true before the stone is measured. Send the length you want, the number of stools, and photographs walking from the pavement through to the room, including the cellar stair if the bar is going down there. Where ownership is split across a building, the common parts belong to someone else and the carry route is negotiated rather than assumed. A home bar is discretionary work, so the edge profile, the corbel detail and the radius on the nose are worth settling properly rather than defaulting to whatever is quickest. Consent for a structural fixing comes before the fitting date.

An island often runs in one piece where a wall run cannot. What you get is a line rather than a step, because the pieces are levelled to each other first. There are only ever a few legal positions, and the one taken is furthest from the light. Knee room under a breakfast bar is measured from the face of the cabinets rather than from the edge of the stone, so a deep apron quietly eats the depth somebody actually gets to sit in. The seating side is the part that decides the piece, because a stool at the open end puts a load on a corner that a wall would otherwise have been carrying. A radius on a walked-past corner is agreed at drawing stage.

Units have to be fitted, fixed and level before templating, and it is better to hear that at the template than on the fitting day. A long top on units that were shimmed once and never checked is the commonest version of this, and it is cheap to fix beforehand. Levelling belongs in the carcasses, on their own legs and packers. A room can be out of square in both directions at once, so the wall that leans is also the wall that runs downhill, and one scribe cannot answer both. Anything that puts a notch in a bar takes material out of the piece at the point people lean on it, so the notch and the support are drawn together or not at all. Anything that flexes under the nose shows up at the join.

If you want the old top kept for a garage or a utility, say so and it stays on site. The template can be taken with the old top still down, which is why one visit covers both. Disposal means it goes in the van, not into the garden to wait for a collection. Where parking runs down both sides the road is left as a single lane, and a van standing in it has to be somewhere it does not stop a bin lorry. A trade bar is fitted around opening times, so the window the van has and the window the room has are rarely the same window. Where the bay is timed, the support goes in first.

Ask for the lines rather than the total. One number for a kitchen tells you nothing you can check. Taking the old tops away is a line rather than an assumption, so it comes off if you do not want it. Two kitchens the same length can be far apart, because material, edge and cut-outs move independently of size. Plaster thickness varies over the height of a wall, so the line at worktop height is not the line at skirting level, and the units decide which one matters. A counter fixed back to lightweight framing takes a sideways push as well as a downward load, and framing built for neither gets noggins let into it first. A column in the middle of a bar is a decision, not a surprise.