Bathroom worktops and vanity tops in Pitshanger

Yes. Pitshanger is on the patch, and the postcodes we work here are W5. It is worked on our west London run, along with the rest of Ealing. A dropped kerb wide enough for a car is not always wide enough for a long-wheelbase van, and the width of the crossing decides the rest. A vanity fit is a short visit with one or two pieces in it, so the van stands only for as long as it takes to walk them in. A vanity fit ends before most parking restrictions do. The template happens in your kitchen and so does the fit, so there is nothing to visit and nothing to collect.

The boiler has usually been moved out to the garage or the utility, leaving a capped flue and a run of dead pipework in the kitchen wall. The original bathroom in these houses is the small room over the hall, and a vanity in it is short, shallow and hard against a wall at each end, so both ends are scribed and there is no tolerance left between them. A large bathroom is where a double vanity becomes possible. The returns into a breast recess are the tightest scribes in the room, and they are eased in rather than forced. Bathrooms carry the same problems in a smaller room, and a smaller room leaves a vanity nowhere to absorb them. The tap has to clear the reveal before the hole is drilled.

Even an easy kerbside carry wants the pavement clear at the tail lift, because a three-metre piece on edge has a swing radius nobody expects until it is swinging. A vanity is the one piece of stone that route will not usually defeat, because a top cut to a standard unit depth weighs what one person can manage. Nobody carries a drilled vanity top by one end. Where a car has to come off the drive first, it is worth knowing whose car it is and whether the keys are in the house on the morning. Where the van cannot wait, the top, the shelves and the adhesive all come in on the first trip and the van goes. The plumber and the van rarely want the street on the same day.

Not especially, and pretending otherwise would be simple enough. What the research on this patch actually lists is worktop design & quotation, worktop installation and worktop fabrication. It is a fact about the local housing rather than about the work. The job is quoted, cut and fitted the same way wherever on the patch it lands. Extension work runs late far more often than it runs early, and the worktop is close to the last thing in, so the date agreed at the start is rarely the date that happens. Work of that kind brings en-suites with it, and an en-suite vanity is a smaller piece again carrying exactly the same four operations. The vanity is the piece that makes a converted flat read finished. Where a family has been living around a building site for months, the finish date carries more weight than any other part of the specification. A house divided into flats needs a vanity for each of them, and small repeated pieces are the one case where buying a whole slab makes sense. Several vanity tops off one slab run, or they will not match.

Waterfall ends are cut in sequence off the length either side of the top so the vein carries down the leg, and that sequence is gone the moment a piece has to be recut. That shape decides what is left on the slab when the kitchen has been cut, and what is left on the slab is where most vanity tops come from. The bathroom is drawn while the kitchen is still on the bench. Supply-only material is £110 to £550 per square metre, and templating, fabrication and fitting are quoted separately rather than rolled in.

An alcove is commonly wider at the back than at the front, so a piece cut to the opening drops in and then stands off the rear wall. A vanity has no depth to lose, so where a kitchen run would take a ten millimetre scribe without noticing, a shallow top cannot spare it. A pipe boxing gets a radiused notch, never a square one. Settle the tiling height and the basin model first, and let us know whether the unit is standing on the floor or hanging off the wall. A quartz sample left on the counter for a week under the actual kitchen lights settles more arguments than any showroom, and an owner is the only person in a position to do that. Who is paying decides the material here more than anywhere else, because a vanity is small enough that an expensive stone stops being an expensive decision. An en-suite in a let flat is specified like the bathroom next door.

What comes out goes by the same route the new stone comes in by, which is why that route is walked before anything is lifted. An old stone top is heavier coming out than the new one is going in, and leaves in sections. The units below stay exactly as they are; only the surface is replaced. A gate post set narrower than the opening looks generous from the road and stops a wide piece a metre in. A bathroom booked on its own rarely fills a day, so it can be put into whichever part of the day the street is easiest. Two pieces and a tube of sealant is the whole delivery.

Small variation is taken up by packing under the top on the fitting day. Variation past what packing can take up has to be corrected in the carcasses before we cut, because the template records the units as they stand. Levelling belongs in the carcasses, on their own legs and packers. The face of a breast is rarely flat, and a top returning onto it picks up that bow across the last few hundred millimetres of its length. A wall-hung unit puts the whole weight into the wall rather than onto the floor, so what the wall is built of stops being a detail. The bridge between aperture and back edge is what a notch eats.

If a piece cannot be got in at all, we say so at the template rather than on the day. A piece travels on edge, never flat, because on edge is how stone of that length carries its own weight. Splitting a run costs a join, and that is the price of getting stone into the room at all. A level threshold with hard standing outside it is the one arrangement where a full run goes in without a single re-grip. What the route really decides for a bathroom is the shelving and the window board, since long thin pieces are the ones that break when they are twisted round a turn. A vanity top goes wherever a person will go.

There are only ever a few legal positions, and the one taken is furthest from the light. Join count and position are settled from the template drawing rather than improvised on the fitting day. An island often runs in one piece where a wall run cannot. Everything on an island is fed from underneath, extraction, a socket run, a hob and sometimes a waste, and each of them wants its hole before the top is bonded down. A bathroom ordered with the kitchen is taken from the same slab run, so the two rooms match rather than nearly match. Offcut stock is the cheapest stone a vanity will ever sit on.