Reception counters and desks in Childs Hill

Yes. Childs Hill is on the patch, and the postcodes we work here are NW2, NW11. It is worked on our north London run, along with the rest of Barnet. Enforcement zones rarely accept a trade van unloading stone as an exemption, so this gets sorted before the date is confirmed rather than argued about afterwards. A commercial frontage rarely has anywhere to stop, so the unload is timed rather than assumed and the counter pieces come off first. Two heights, one unload, one trip across the pavement. Template and fit both happen at the property, so there is nothing to drive to and nothing to collect.

The communal stair is wide and handsome and the flat door at the top of it is a standard leaf, which is where a long piece stops. The commercial work around housing of this age is shopfront: a narrow unit off a high-street parade, entered up a step, with the reception running back from the door into the depth of the plan. Housing office counters get cleaned harder than they get used. A boxed soil stack or service riser in the corner of a run eats into the worktop depth and has to be scribed around rather than cut square. A counter is worse off than a kitchen here, because it usually stands clear of the wall and has nothing behind it to hide a gap. The back return follows the wall as the wall leans.

A handrail that has to come off before a piece will pass is twenty minutes at the start of the day, and it goes back on the wall before we leave. A counter top is one long piece with no run of cabinets to break it, so the route decides the join count before the sightlines get a vote. The counter is sized to the way in before it is sized to the slab. Visitor permits are issued to the household rather than to the trade, so the ones the day needs come from the customer and are best in hand the week before. Loading bays belonging to the building are booked by whoever holds the lease, and that is seldom whoever ordered the counter. The van stays put while the carcass is being scribed to.

Not particularly. It would be easy to say yes and leave it there. What the research on this patch actually lists is worktop replacement, worktop templating and worktop splashbacks & upstands. That is about what people have here rather than how it gets done. It is quoted, cut and fitted exactly the same way here as anywhere else on the patch. Studio and one-bed conversions put the whole kitchen against a single wall, so the job is one run and everything depends on that one length. Counters are nearly always one-offs, so the saving that comes from repeating a specification is not usually on the table here. Matching across sites means matching blocks, not matching names. A kitchen carved out of a larger room sits under whatever the original plan left behind, so the run frequently ends at a blocked doorway or a boxed-in service. Where an operator is fitting out several receptions, the counters come off one slab run so the desks read as a set rather than as neighbours. The counter is quoted with the programme written beside it.

Walls at both ends mean two scribes on every piece, and a run that has to drop between two fixed points has no tolerance left to give away. A counter has the same argument in miniature: a straight run nests kindly on a slab, and every return costs yield. The return between the two levels is drawn first and cut first. Expect £110 to £550 per square metre for material supply only, with templating, fabrication and fitting on their own lines.

Boxing is rarely the same depth at worktop height as it is at floor level, so measuring it low down is the usual reason a top will not sit back. What a counter is scribed to is the joiner's carcass rather than the plaster, which is why it is templated after the carcass is fixed and never before. Column casings take machined returns, not filler. Send photographs taken walking from the pavement through the door to where the counter will stand, along with the carcass dimensions once the joiner has fixed it. Some doors in a building need a consent letter and some need nothing at all, so the first question is which arrangement applies here rather than which one is usual. The same split runs through commercial property: a landlord fitting out a shell and a tenant fitting out their own reception want different things from one counter. Approval in writing before a slab is committed to a desk.

A seal is not waterproofing. It only buys time to wipe a spill up. Upkeep is settled when the slab is chosen, since it belongs to the material rather than the fabrication. Granite tells you when the seal wants topping up: water stops beading on the surface and starts darkening it instead. Kitchens in the upper flats often sit in the return wing at half-landing level, so there are three or four steps inside the flat before the room is reached at all. That entrance is what caps the counter, because a shopfront door and the step in front of it will take far less than a full-length top, so the run is broken over a support in the carcass rather than gambled on. A converted house wants a counter that reads as furniture.

Upstands and splashbacks are templated after the worktop is down and settled, so they are a separate visit. Nothing is payable in advance of the template. The fitting itself is one visit: a plain run is a morning, an island with splashbacks takes most of the day. A cast iron soil stack runs down the outside of the rear wall, so moving the sink means a fresh penetration through solid brick. A reception counter answers to the building it stands in more than to the drawing, because it is fabricated to a carcass somebody else has already built and fixed. A reception is in use the morning after, and that sets the sequence.

Stone does not flex, so a run that rocks on its carcasses rocks just as badly once it is stone. Levelling belongs in the carcasses, on their own legs and packers. Units have to be fitted, fixed and level before templating, and it is better to hear that at the template than on the fitting day. Anything that has to stay accessible, a stopcock, a gas meter, a riser panel, is marked on the template so the stone is cut around it instead of over it. A lobby wall that leans shows itself along the back return, so that edge is cut to the line the wall actually takes. What is out of true gets measured, not talked around.

Sinks, taps and hobs are yours to buy in any case, and they only have to be in the room for the template. Supply through us runs £110 to £550 per square metre for the slab alone, which is the line you would be removing. Stone cut to somebody else’s drawing cannot usefully be re-cut to yours. Conversions put kitchens where the services could be made to reach rather than where they belong, so runs are short and interrupted. A fit-out programme puts the counter last, behind the joiner and the electrician, which is exactly when the least time is left to template it. Where the lobby stays open, the work runs outside opening hours.