Reception counters and desks in Fortis Green

Yes. Fortis Green is on the patch, and the postcodes we work here are N10, N2. It is worked on our north London run, along with the rest of Haringey. Unrestricted does not mean empty, and a street that is clear at seven is usually full by nine. A commercial frontage rarely has anywhere to stop, so the unload is timed rather than assumed and the counter pieces come off first. Whoever holds the lease usually holds the loading bay. There is nothing to drive to and nothing to pick up, because both visits are to the property itself.

These were built late enough to have a damp course and proper footings, so the front of the house is close to true and the rear addition holding the kitchen is the part that has dropped. The commercial work around housing of this age is shopfront: a narrow unit off a high-street parade, entered up a step, with the reception running back from the door into the depth of the plan. A stair off the pavement caps what can be turned onto the landing. A run can measure dead right at both ends and still belly out in the middle, which only appears once the template plots the intermediate points. What a counter is scribed to is the joiner's carcass rather than the plaster, which is why it is templated after the carcass is fixed and never before. Stone will not straighten joinery, and it will not forgive it either.

A meter cupboard set into the hall wall narrows the run at exactly the height a carried piece travels. A counter top is one long piece with no run of cabinets to break it, so the route decides the join count before the sightlines get a vote. Piece length is capped in the drawing office, not on the landing. A skip, a delivery lorry or a run of scaffolding takes the frontage the van needed, so the street is worth a look the day before rather than on the morning. Loading bays belonging to the building are booked by whoever holds the lease, and that is seldom whoever ordered the counter. The longest counter piece decides the swing radius outside.

Honestly, no, though it would be easy to claim otherwise. What the research on this patch actually lists is worktop replacement, worktop templating and worktop installation. That says something about the housing round here, not about the work. Quote, cut and fit are the same here as on any other part of the patch. Rear and side-return extensions are where the islands appear, and an island is the piece that decides whether one slab does the kitchen or two. Counters are nearly always one-offs, so the saving that comes from repeating a specification is not usually on the table here. The knee recess is not a variable between sites. A new extension slab is not automatically level, and that wants checking before templating rather than after the stone is cut. Where an operator is fitting out several receptions, the counters come off one slab run so the desks read as a set rather than as neighbours. A counter in a working building is an evening job.

Butt-jointing over the gable puts the seam a few hundred millimetres back from the corner, below the eye line instead of straight across it. A counter has the same argument in miniature: a straight run nests kindly on a slab, and every return costs yield. A counter join lines up with the plane above it or it gets moved. Expect £110 to £550 per square metre for material supply only, with templating, fabrication and fitting on their own lines.

Where a corner is a couple of degrees off, a mitre cut to a theoretical ninety degrees opens on the wall side and there is no closing it afterwards. A lobby wall that leans shows itself along the back return, so that edge is cut to the line the wall actually takes. The front edge runs straight whatever the wall behind it does. Send photographs taken walking from the pavement through the door to where the counter will stand, along with the carcass dimensions once the joiner has fixed it. One staircase can serve an owner on the first floor and a managed tenancy on the second, so the access arrangement changes at every landing while the building stays the same. The same split runs through commercial property: a landlord fitting out a shell and a tenant fitting out their own reception want different things from one counter. The counter drawing is signed by whoever is paying for it.

A join forced by the route still sits over a gable, so it is no poorer a join for that. An external stair, a side return or a rear garden counts as carry and is measured the same way. The alternative to a join is a shorter run, which is usually the wrong thing to trade away. Whether the kitchen sits straight ahead or off a turn at the end of the hall changes the maximum piece far more than the hall width does. The lower transaction shelf is short and easily handled; it is the upper counter that has to be walked in on edge and turned at every corner. A goods lift diagonal belongs on the counter drawing.

Nothing is payable until the template, and the template measures the room as it stands rather than estimating from a plan. Plumbing, gas and electrical work are not in the figure, because we do not do them. Taking the old tops away is a line rather than an assumption, so it comes off if you do not want it. The stone carries the scribe because the wall cannot be persuaded, so back edges are cut oversize and eased in rather than dropped straight down. Where the floor falls away across a lobby the carcass is packed level first, because the top cannot correct anything sitting under it. Where the plaster bows, the counter is drawn away from it.

Upkeep is settled when the slab is chosen, since it belongs to the material rather than the fabrication. Bleach and limescale remover harm a polished finish rather than clean it, whichever material is on the units. Granite tells you when the seal wants topping up: water stops beading on the surface and starts darkening it instead. The kitchen occupies the ground floor of the addition with a garden door at the far end, so there is a second way in that is narrower than the front door and a great deal shorter. The commercial work around housing of this age is shopfront: a narrow deep unit off a parade, with the reception running back from the door into the depth of the plan. Steel and brick leave a desk nothing to lean against.

The tap hole is drilled in the workshop too, and its position depends on how far the tap has to swing. Two bowls means two cut-outs and a bridge of stone between them, which decides where the sink can go. We seat and seal the sink and hob on the day; water, waste, gas and electrics are for your plumber and electrician. Corner sinks and corner hobs sit exactly where the joint wants to be, so on an L the cut-out positions get settled before the join positions do. The return between the high counter and the low shelf never nests neatly, and it is what decides how much slab the desk swallows. Yield on a counter is lost in the returns, not in the length.