Stone bar tops in Tottenham Green

Yes. Tottenham Green is on the patch, and the postcodes we work here are N15, N17. It is worked on our north London run, along with the rest of Haringey. The realistic answer on a main road is an early slot, a spotter on the van and pieces staged in one movement rather than several trips. That has to cover more than the unload, since the corbels, the flat bar and the fixings all come off the van well before the top does. The nose stays wrapped until the frame is ready for it. Both visits happen in your kitchen, the template and the fit, so there is nothing to visit and nothing to collect.

These kitchens are big rooms with long perimeter runs and an island, so level has to hold across the whole floor rather than along one wall. Lengths run past what a single slab gives, so a break is designed in from the start, placed over support and kept clear of every stool position before anything is nested. Old floors move, so the bar is fixed back as well as down. Boxing is rarely the same depth at worktop height as it is at floor level, so measuring it low down is the usual reason a top will not sit back. On a bar that counts twice over, because the same obstruction has to be cleared by the stone above it and by the knees of whoever is sitting at it. The riser is boxed to a line the stone can follow.

Booked delivery windows on a managed estate run to an hour, and a worktop install does not happen inside an hour. That matters more on a bar than on a run, because a join forced by the way in cannot be allowed to land in the unsupported part of the nose. Stools and back shelving come in after the stone is down. A single red line has hours and a double red line does not, and the difference decides whether an early start is a plan or a penalty. A trade bar is fitted around opening times, so the window the van has and the window the room has are rarely the same window. Fitting a bar top is slower than carrying one.

Honestly, no, though it would be easy to claim otherwise. What the research on this patch actually lists is worktop templating, worktop installation and worktop replacement. That says something about the housing round here, not about the work. Quote, cut and fit are the same here as on any other part of the patch. Studio and one-bed conversions put the whole kitchen against a single wall, so the job is one run and everything depends on that one length. A bar is nearly always the last thing added to a project, so it is templated on a visit of its own once the joinery around it has stopped moving. Where the use is hard, the surface is chosen for it. A kitchen carved out of a larger room sits under whatever the original plan left behind, so the run frequently ends at a blocked doorway or a boxed-in service. Where the same detail is repeating across several rooms the support gets standardised once and then cut to length, which is cheaper than drawing it each time. A late bar is a separate visit and the quote says so.

An aisle under a metre stops being a working space the moment two people are in it, and the depth of the tops either side is what decides whether that happens. Where the counter runs flush with the working surface instead of standing above it the whole thing becomes one plane, which looks better and doubles the unsupported span. Where the two levels meet is a detail, not an afterthought. Material runs £110 to £550 per square metre supply only, and templating, fabrication and fitting each get their own line.

Anything that has to stay accessible, a stopcock, a gas meter, a riser panel, is marked on the template so the stone is cut around it instead of over it. A bar top is levelled to itself rather than to what it stands on, so the packing goes into the frame and the stools take up whatever the floor is doing. Steel spans what a carcass cannot. Send the bar layout with the rear counter and any sink marked, the seating side and stool count, and the edge profile you want on the front. The householder is normally on site at template, and that is the right time to settle sink position, tap centres and overhang rather than agree them by email. A home bar is discretionary work, so the edge profile, the corbel detail and the radius on the nose are worth settling properly rather than defaulting to whatever is quickest. Fixings into structure are agreed before they are drilled.

A long top on units that were shimmed once and never checked is the commonest version of this, and it is cheap to fix beforehand. If the carcasses are corrected, the template is taken again, since a drawing off units that then moved is worthless. Variation past what packing can take up has to be corrected in the carcasses before we cut, because the template records the units as they stand. A notch around a boxed stack is machined with a radius at the internal corner, because a square inside corner there is exactly where a top will crack. Where the nose has to be carried past something fixed the support moves rather than the stone, since a corbel landing in the knee space is worse than no corbel at all. A bar top is set to one datum along its own length.

Granite tells you when the seal wants topping up: water stops beading on the surface and starts darkening it instead. Granite is porous to varying degrees, so it is sealed when we fit it and topped up over the life of the worktop. Bleach and limescale remover harm a polished finish rather than clean it, whichever material is on the units. Original walls are thick, lime-plastered and rarely straight, which makes dry-laying and scribing the bulk of the fitting day. There is normally room here for a genuine bar rather than a seating overhang, which means a rear counter, a small sink and a run of shelving all drawn as one piece of joinery. A bar in a small room is drawn for the stools it will take.

The design and quotation visit comes first. It is free and carries no obligation. Nothing is measured until the sink, the tap and the hob are in the room to measure against. There is nothing to pay before the template visit. Sliding or folding doors take the whole garden wall, so a long stretch of the room has glass where a wall would otherwise carry the units. A bar top put into a room like that is an overhang question first, because the nose has to carry people leaning on it long after the slab has stopped being interesting. A bar top is a structural piece with a polished face on it.

A join is glued and clamped flush on the day, so it is fixed rather than something to be undone. Dark and heavily veined stone shows a join more than a pale even one, which is worth knowing before the slab is picked. A join sits over a cabinet gable. It never spans a gap and never runs through a cut-out. A dishwasher door on one side and an oven door on the other cannot both stand open in a narrow aisle, so which appliance goes where matters more in this shape than in any other. The seating side is the part that decides the piece, because a stool at the open end puts a load on a corner that a wall would otherwise have been carrying. Stools need floor as well as knee room, and both are drawn.