Stone worktops in Haydons Road

Yes. Haydons Road is on the patch, and the postcodes we work here are SW19. It is worked on our south west London run, along with the rest of Merton. A short lunchtime window of control exists to keep commuters off the street, and it still catches a trade van standing there for an hour. Whatever the standing allows, the stone leaves that van finished, because every edge, cut-out and internal radius is machined at the works and none of it is open to reconsideration at the kerb. What stands on the van is finished stone, not raw slab. Both visits happen in your kitchen, the template and the fit, so there is nothing to visit and nothing to collect.

Floors are the original joists with a later acoustic layer laid over them, and that layer is not flat where it meets the doorways. The kitchen in one of these sits in the back addition and takes its daylight from one end, so the working half of the run is the darker half and a pale stone with a honed or matt face does more there than any colour with depth in it. Open-plan surfaces are furniture before they are work surfaces. A live soil stack cannot be chased back into the wall, so the depth it steals is permanent and the run is planned around it rather than through it. Every notch and every scribe is machined into the piece before it leaves the works, and a hard sintered surface is the least forgiving of a tight internal corner, so one is always cut with a generous radius. Every notch is machined on the bench and none on site.

A handrail that has to come off before a piece will pass is twenty minutes at the start of the day, and it goes back on the wall before we leave. That caps the longest piece, and a run split into two lengths nests differently on the slab, which moves the yield and moves the figure with it. No colour and no edge is adjustable once a piece is machined. Where the nearest legal space is a couple of streets back, the walk with each piece becomes the job, and the crew is sized for walking rather than wheeling. A granite kitchen ends its day with a sealer, and a sealer wants a dry face and a quiet hour afterwards, so that hour is written into the day rather than borrowed from it. Nothing about the shortlist is decided on the day itself.

The two runs are rarely the same length, and the shorter one often carries the sink, which puts the cut-outs in the piece with the least material to spare. A shape like that nests kindly on a slab, so more of what gets bought ends up on the units and the rate per square metre behaves much as the brochure says it will. A single straight run is the cheapest stone you will ever buy. Reckon on £110 to £550 per square metre for the material supply only, with templating, fabrication and fitting itemised separately.

Boxing built in plasterboard on a light frame will take no useful fixing, so nothing bears on it and the stone is carried off the carcasses either side. A hob dropped into the middle of a length puts sustained warmth at the lip of a cut-out, and an engineered surface will yellow there across ten years where a natural one takes it without comment. Water standing daily is what makes porosity matter. Send the run lengths, say where the sink and hob will sit, and tell us which way the room faces and what lighting is going in above the working run. Some doors in a building need a consent letter and some need nothing at all, so the first question is which arrangement applies here rather than which one is usual. That changes which questions are worth asking about the stone, because somebody staying put wants to know how a honed face marks in five years and somebody selling wants to know how it photographs next spring. Cleaning spray, not showroom light, should decide the finish.

Chips at an edge or a corner are the usual form, because that is where stone is least supported. Most breakages happen on the carry, which is why the route is walked and measured before anything comes off the van. A remake goes back through the same cutting and polishing, so it is a return visit rather than a patch. Spindles and a newel cap stand proud of the string, so the usable width on a turn is measured to the handrail rather than to the wall behind it. Where a seam becomes unavoidable the choice of stone starts to matter, because a fine even speckle closes a joint almost invisibly and a broad vein simply will not. Yield drops the moment the building dictates awkward lengths.

Quartz carries resin, so a hot pan wants a trivet, while granite and sintered stone will take one without complaint. Sealing is the one maintenance job that genuinely differs by material, and it is worth knowing which you are buying before the slab is chosen. Bleach and limescale remover harm a polished finish rather than clean it, whichever material is on the units. The communal stair is wide and handsome and the flat door at the top of it is a standard leaf, which is where a long piece stops. Alcoves either side of the old breast chop the run into short lengths, and a kitchen made of short lengths is the case where buying a slab outright beats buying the square metres, because the remainder is paid for in both. True walls and standard carcasses give the best yield there is.

If the sink or hob changes after the template, the drawing changes first and nothing is cut meanwhile. A sit-on sink and an undermounted one are different cut-outs, so which it is gets settled before the template. We seat and seal the sink and hob on the day; water, waste, gas and electrics are for your plumber and electrician. A tall bank of housings at one end takes a chunk out of the working run, so the usable length of that side is always less than the length of the wall behind it. An island is the piece that decides whether one slab covers the kitchen or two, and a second slab arrives as a step in the figure rather than a gentle slope. Nesting is where the quiet savings on a kitchen live.

Tiling bonded to the wall behind usually comes away with the old top, so that wall is agreed beforehand. The tap and waste have to be disconnected by a plumber before we start and reconnected once the stone is in. The sink and hob are lifted out with the old top and kept aside if you are reusing them. Applying for a suspension means naming a length of kerb and a date, and moving the date generally means applying for it again. Sintered surfaces are the hardest of the three to machine and the messiest to cut wet, which is precisely why none of that happens on a public pavement. A figured slab takes longer to match than a plain one.