Worktop replacement in Chalk Farm

Yes. Chalk Farm is on the patch, and the postcodes we work here are NW1, NW3. It is worked on our central and north London run, along with the rest of Camden. A single red line has hours and a double red line does not, and the difference decides whether an early start is a plan or a penalty. A replacement is a two-way job, with old tops going out and new stone coming in, so the van needs to stay put across the whole day. A one-hour window will not hold a two-way job. The measuring and the fitting are both done at the property, so there is nothing to visit or collect.

Floor to ceiling heights are tight on the upper levels because the original building had none to spare. These are the multi-piece jobs: long runs, a large island and often a range cooker that cannot be moved, so the stone is templated in several pieces and how the vein runs across the joins matters. Everything the last fit ignored is visible for a morning. Where a breast interrupts a long wall the join can often go there, so it reads as a natural break rather than a line in the middle of a worktop. The old top has been hiding it, so the first honest look at it happens when the laminate comes off. A postformed top swallowed the fall. This will not.

The front door is often the cheapest hundred millimetres on the route, because a door lifted off its hinges gives back the width its own thickness was taking. Worth remembering that the old tops have to come out the way the new ones come in, and a laminate run is easier to remove in one length than to carry in one. Whether the strip-out is a cut-up job is settled at template. Where a marked loading box sits on the red route the stop is legal but timed, so the unload runs as one movement with every hand on it. Waste is the part people forget: the old laminate or tired granite has to be walked back to the van and it does not get lighter. The strip-out waits until the new stone has somewhere to stand.

Yes. On the research for this patch it is the first of the three jobs listed, ahead of worktop installation. Extension work runs late far more often than it runs early, and the worktop is close to the last thing in, so the date agreed at the start is rarely the date that happens. The units stay and only the surface changes, so the whole job is one day rather than a kitchen refit. Old top out Tuesday, tenant in on Friday. Where a family has been living around a building site for months, the finish date carries more weight than any other part of the specification. The carcasses have to be sound, because stone is several times the weight of what is coming off. The flat earns nothing while it sits empty.

An aisle under a metre stops being a working space the moment two people are in it, and the depth of the tops either side is what decides whether that happens. The existing layout is being kept, so the question is whether the old carcasses will take stone in that shape without more support. The sink is chosen before the cut list is set. Material alone is £110 to £550 per square metre, and templating, fabrication and fitting are never folded into that figure.

The returns into a breast recess are the tightest scribes in the room, and they are eased in rather than forced. This is the commonest reason a replacement turns out to need more than a straight swap. The alcove was never square and it still is not. Have a fitter or joiner fix and level the island units beforehand, and get the sink, taps, hob and any range on site before templating so we cut to the actual appliances. Where ownership is split across a building, the common parts belong to someone else and the carry route is negotiated rather than assumed. A replacement keeps the units and changes the surface, which is the least disruptive way to do this in an occupied property. Strip-out and fit inside one access window.

Doorways, the newel post and the handrail usually take the room away, rather than the stairs themselves. Hoisting through a window is occasionally the answer, and it is a decision made at the template, not improvised on the fitting day. The alternative to a join is a shorter run, which is usually the wrong thing to trade away. An inward-opening door swinging back against the wall leaves less clear opening than the frame measures, and a storm porch in front of it is tighter again. With no room to turn, the old top gets cut up in the kitchen instead, which is dusty work and needs the room emptied first. Two carries in one day needs the route free for both.

If the carcasses are corrected, the template is taken again, since a drawing off units that then moved is worthless. Where a run meets an appliance, level decides whether that appliance door still clears the stone above it. The check comes before the measuring rather than after, because the whole drawing is set out from that plane. An alcove is commonly wider at the back than at the front, so a piece cut to the opening drops in and then stands off the rear wall. A laminate top was scribed thin at the back to swallow it, and stone cannot be shaved down the same way. What passed for a fit in chipboard will not pass in stone.

Old tops are screwed or glued from underneath, so the drawer boxes come out before the worktop does. Take the old tops off yourself if you would rather, and the quote simply carries one line fewer. The units stay where they are and only the surface changes. A bus lane along the frontage brings its own hours with it, and stopping in one is enforced the same way the red route is. We stage the strip-out so the old tops leave in one trip rather than trickling out across the afternoon. Loading out is loading in, done in reverse and heavier.

Day to day all three want soap and water; abrasive creams and scouring pads are what dull a polished surface. Upkeep is settled when the slab is chosen, since it belongs to the material rather than the fabrication. The bead where the sink and hob meet the stone is siliconed rather than sealed, and wants watching. Where the roof has been raised, a steel frame went in with it and its columns land inside the finished walls. Any island overhang past about 300mm will not carry weight on the carcass alone, so flat steel bar or brackets have to be let into the units first, and that is agreed at template stage, not on fit day. The shell is the constant here; the surface is not.