Worktop installation in Hither Green

Yes. Hither Green is on the patch, and the postcodes we work here are SE13, SE12. It is worked on our south east London run, along with the rest of Lewisham. A controlled parking zone means either a visitor permit sorted in advance or a suspended bay, and a suspension is applied for days ahead rather than on the morning. The fitting slot is set around it, which is why we ask about it when the date is booked and not before we leave the yard. Camera enforcement does not take an explanation. There is nothing to drive to and nothing to pick up, because both visits are to the property itself.

Internal walls are lath on timber studs while the flank walls are brick, so two walls in the same kitchen take a fixing completely differently. We measure the front door, the hall width and the turn into the kitchen before anything comes off the van, because a 3m piece has to swing through that corner on edge and stone does not bend to help you. The shell has the last word on fitting day. Plaster thickness varies over the height of a wall, so the line at worktop height is not the line at skirting level, and the units decide which one matters. On the day it means dry-laying, marking, and cutting the scribe on site before anything is bonded. The last hundred millimetres decide how it reads.

A side gate hung to open outward against a fence post is narrower in use than it measures, and lifting the gate off its hinges is usually the quickest win on the route. The fitting day is planned backwards from that point, before anything comes off the van. We would sooner lift a gate off its hinges than force a piece past it. Permit hours are what matters, not the permit itself, because a bay that frees up at six in the evening is no use for a template at ten. A van that has to move mid-fit costs the best part of an hour and takes a man off the tools to do it. Forty metres of carry changes the shape of the whole day.

Yes. On the research for this patch it is the first of the three jobs listed, ahead of worktop fabrication. Extension budgets are usually well spent by the time the worktop is ordered, which is where the choice between quartz and a thinner sintered stone actually gets made. The fitting day is scheduled to suit that rather than to suit the diary. Plot after plot, the same fitting sequence. Rear and side-return extensions are where the islands appear, and an island is the piece that decides whether one slab does the kitchen or two. Where the window is fixed there is no second day to fall back on, so the prep list matters more than usual. Lease hours decide when the noisy part happens.

An island is a single visible piece with four finished edges and no wall to hide against, so it is the piece the whole kitchen is judged on. On the day that means dry-laying the whole layout first and only then pulling and bonding the joins. A galley is levelled as one plane, both sides together. Reckon on £110 to £550 per square metre for the material supply only, with templating, fabrication and fitting itemised separately.

Two walls each a degree out give an internal corner two degrees out, and the whole of that error lands in the mitre. Rushing that is what leaves a gap you look at every morning for fifteen years. If it will not drop in, it goes back out to the saw. Clear the full hall and stairs route of furniture, bikes, coats and stair-gates, and keep the front door propped and unobstructed for the carry. One staircase can serve an owner on the first floor and a managed tenancy on the second, so the access arrangement changes at every landing while the building stays the same. The fitting day is arranged with whoever can actually give us access for the whole slot. Emptying the room belongs to the keyholder, not the crew.

The workmanship guarantee runs 5 years on every kitchen we fit. The rest of the kitchen still goes in. One damaged piece does not hold up the pieces either side. Our own installers do the carry, so there is nobody in the middle to argue with about it. Where the garden is level and the back door is wide the pieces get staged outside on trestles and brought in one at a time as the fitters are ready for them. Finding it out on the morning costs the whole slot, because there is no second route to fall back on. That is what the morning is planned around.

The design and quotation visit comes first. It is free and carries no obligation. Upstands and splashbacks are templated after the worktop is down and settled, so they are a separate visit. On the fitting day floors and door frames are protected, joins clamped flush, sink and hob sealed. The rear wall of the addition carries both the back door and the window, which leaves very little unbroken wall for a run to sit against. The fitting day is planned backwards from all of it, before the first piece comes off the van. The first hour is protection and packing, not stone.

Undermount bowls are cut and polished in the workshop and dry-fitted to the stone on the bench before anything is loaded. A boiling tap needs a hole of its own and a cupboard below for the tank, so the units change too. A tap under a window board still needs room for its handle to lift, which is checked at the template. If the island is a few hundred millimetres longer than the usable length of a slab, a second slab gets bought to gain that overhang, and the whole slab is paid for rather than the part used. A layout that has been packed and levelled run by run instead of to one datum shows as a step where two pieces meet. The last piece in has the least tolerance left.

Thickness has to be known before quoting, since it decides the edge, the cut-outs and what the units carry. Remnants bought elsewhere are the awkward case, because the drawing is then made to fit the stone. A new extension slab is not automatically level, and that wants checking before templating rather than after the stone is cut. One visit, with the sink and hob seated and sealed before we leave. A tenant moves in on the date on the contract.