Stone bar tops in South Bermondsey

Yes. South Bermondsey is on the patch, and the postcodes we work here are SE16. It is worked on our south east London run, along with the rest of Southwark. An event-day suspension can override a bay that is perfectly usable the rest of the week, so a booked space gets checked again nearer the time. A bar fit runs longer than a worktop run, because the frame, the support and the stone are three stages and only the last of them is quick. A licensed room sets the hours and the parking has to agree. We come to the kitchen to template and again to fit, so there is nothing to visit and nothing to collect.

A service duct runs between the kitchen and the bathroom stacked above it, and access to that duct stays open whatever the layout does. Rooms in this stock are compact, so a bar usually replaces a table rather than sitting alongside one, and it is drawn for two or three stools with enough floor left to get past them. A breakfast counter on an end is still an overhang problem. Where the boxing stands proud of the finished wall the upstand behind it has to be broken into separate lengths, because one piece cannot pass it. On a bar that counts twice over, because the same obstruction has to be cleared by the stone above it and by the knees of whoever is sitting at it. The knee space is measured before the bracket is specified.

A rated load sounds ample until three lengths of granite and two fitters are standing on it, so the stone goes up one piece at a time. That matters more on a bar than on a run, because a join forced by the way in cannot be allowed to land in the unsupported part of the nose. Where the way in is awkward the bar is drawn in tiers. Where a road is shut for filming or for works the diversion adds distance to the carry even when parking itself was never the problem. That has to cover more than the unload, since the corbels, the flat bar and the fixings all come off the van well before the top does. Nothing is rushed off a tail lift onto an unsupported nose.

No, not particularly, and it would be easy to say otherwise. What the research on this patch actually lists is worktop replacement, worktop installation and worktop splashbacks & upstands. That is the local housing talking rather than anything about the job. It is priced, cut and fitted no differently here than anywhere else we cover. Agents book this work at short notice, because the void only becomes a real date once the outgoing tenant confirms they are going. A bar is nearly always the last thing added to a project, so it is templated on a visit of its own once the joinery around it has stopped moving. What was drawn and what was built are compared at template. A managed portfolio tends to repeat one specification across every flat, which keeps later repairs and replacements simple to order. Where the same detail is repeating across several rooms the support gets standardised once and then cut to length, which is cheaper than drawing it each time. A bar is templated after the joinery has stopped moving.

Two runs meeting at an internal corner is the most common shape we fit, and the corner is where the decisions are. A bar laid over that is a second level rather than a wider one, so it wants a spine underneath it and a settled detail where the two heights meet. Nothing sits over a join that somebody leans on. The material band is £110 to £550 per square metre supply only, and templating, fabrication and fitting are quoted on their own lines.

A boxed soil stack or service riser in the corner of a run eats into the worktop depth and has to be scribed around rather than cut square. A bar top is levelled to itself rather than to what it stands on, so the packing goes into the frame and the stools take up whatever the floor is doing. Where the wall is bowed the rear rail takes it up. Send a photograph of every corner of the room so we can see the boxings, the length you want, and how many stools you expect to use. Consent for the work sits with the freeholder or the managing body, and getting it in writing first avoids a crew arriving to a locked door. A home bar is discretionary work, so the edge profile, the corbel detail and the radius on the nose are worth settling properly rather than defaulting to whatever is quickest. A bar in constant hands wants a finish that does not mark.

The check comes before the measuring rather than after, because the whole drawing is set out from that plane. Levelling belongs in the carcasses, on their own legs and packers. Where a run meets an appliance, level decides whether that appliance door still clears the stone above it. Boxing is rarely the same depth at worktop height as it is at floor level, so measuring it low down is the usual reason a top will not sit back. Where the nose has to be carried past something fixed the support moves rather than the stone, since a corbel landing in the knee space is worse than no corbel at all. A bar pushed sideways was fixed to plasterboard.

We seat and seal the sink and hob on the day; water, waste, gas and electrics are for your plumber and electrician. A tap under a window board still needs room for its handle to lift, which is checked at the template. A sit-on sink and an undermounted one are different cut-outs, so which it is gets settled before the template. The return piece is the awkward one on a slab: short, full depth, and rarely nesting neatly against the long lengths, so yield rather than area is what moves the material figure. Where the counter runs flush with the working surface instead of standing above it the whole thing becomes one plane, which looks better and doubles the unsupported span. The overhang is drawn before the layout is signed off.

Which side of the bowl they go is about how you stand at the sink, and it is settled before cutting. The alternative stands on the surface, so the choice is losing worktop permanently or only while you are draining. They read strongly across a dark stone and are nearly invisible on a pale one, so look before deciding. Internal partitions are dense block finished in a hard sand and cement plaster, which is unforgiving to drill and unforgiving to make good. A bar top put into a room like that is an overhang question first, because the nose has to carry people leaning on it long after the slab has stopped being interesting. A bar top is judged from a stool, not from the doorway.

A join sits over a cabinet gable. It never spans a gap and never runs through a cut-out. Slabs come in finite sizes, so a long run needs a join whatever the room looks like. Join count is a question about slab size and run length, nothing else. An L can be mitred at the corner for a continuous look or butt-jointed over the gable, and the two are different money and different risk. The seating side is the part that decides the piece, because a stool at the open end puts a load on a corner that a wall would otherwise have been carrying. A bar top is a shape decision with steel attached to it.