Worktop replacement in Alibon

Yes. Alibon is on the patch, and the postcodes we work here are RM10. It is worked on our east London run, along with the rest of Barking and Dagenham. Unrestricted kerbside is straightforward as long as the space in front of the property is actually clear when the van arrives. A replacement is a two-way job, with old tops going out and new stone coming in, so the van needs to stay put across the whole day. Nothing goes out until the route back to the van is clear. The work comes to you. We template in your kitchen and fit in your kitchen, with nothing to visit or collect.

A service duct runs between the kitchen and the bathroom stacked above it, and access to that duct stays open whatever the layout does. Ex-council flats and maisonettes are built in dense concrete and blockwork, so anything that has to be fixed back, such as brackets under a peninsula or support for an end panel, goes in with proper anchors and an SDS rather than plasterboard fixings. Nothing goes back on carcasses the building has pulled out of square. A live soil stack cannot be chased back into the wall, so the depth it steals is permanent and the run is planned around it rather than through it. The old top has been hiding it, so the first honest look at it happens when the laminate comes off. It is the usual surprise, and it is a known one.

Carrying down a flight is not the easier direction, because the weight runs ahead of the crew and whoever is at the bottom has no way of stopping a slip. Worth remembering that the old tops have to come out the way the new ones come in, and a laminate run is easier to remove in one length than to carry in one. Timing the two carries is most of the planning. On a street with no restrictions the constraint is other residents rather than a warden, so it is worth putting a cone or a car out early. Waste is the part people forget: the old laminate or tired granite has to be walked back to the van and it does not get lighter. The old tops leave in one movement rather than piece by piece.

Yes. On the research for this patch it is the first of the three jobs listed, ahead of worktop installation. Damage in a let flat is settled as a deposit deduction, so a surface that can be repaired in place is worth more than one that has to be replaced whole. The units stay and only the surface changes, so the whole job is one day rather than a kitchen refit. Specified for wear rather than for the photograph. The person choosing the worktop is not the person using it, and that shifts the balance from appearance towards running cost. The carcasses have to be sound, because stone is several times the weight of what is coming off. No sealing schedule for anybody to forget.

An L can be mitred at the corner for a continuous look or butt-jointed over the gable, and the two are different money and different risk. The existing layout is being kept, so the question is whether the old carcasses will take stone in that shape without more support. The return is remeasured even where it looks unchanged. The material band is £110 to £550 per square metre supply only, and templating, fabrication and fitting are quoted on their own lines.

Boxing built in plasterboard on a light frame will take no useful fixing, so nothing bears on it and the stone is carried off the carcasses either side. This is the commonest reason a replacement turns out to need more than a straight swap. It was there long before we were. Sort a parking bay or permit near the entrance, confirm the lift is in service and get us the door codes, and tell us about any asbestos survey on the flat before we start stripping out. Residents are given written notice before anyone attends, and that notice period rather than the workshop is what governs the earliest sensible start. A replacement keeps the units and changes the surface, which is the least disruptive way to do this in an occupied property. One day out of use, agreed in advance.

Packing takes up small variation. It is not there to hide something that belongs in the units. A long top on units that were shimmed once and never checked is the commonest version of this, and it is cheap to fix beforehand. Levelling belongs in the carcasses, on their own legs and packers. A stack boxed diagonally across a corner leaves a triangle of dead space, and the top is cut to that triangle rather than to a square return. We would rather find it at template than on the morning, which is why the templater looks behind the units. The old top hid it. The drawing will not.

What decides it is not the width of the stairwell but the length of piece that can be turned in it. Every piece goes in by hand and stone does not bend, so the tightest turn on the route sets the longest piece. Splitting a run costs a join, and that is the price of getting stone into the room at all. A short run of external steps before the communal door means a piece is lifted twice before the staircase proper has even started. With no room to turn, the old top gets cut up in the kitchen instead, which is dusty work and needs the room emptied first. The room is cleared for the way out as much as the way in.

A dropped pan years later is a different question, and stone is remade rather than filled either way. A piece is never laid flat across a gap while it is moved, because that is how stone cracks unaided. The workmanship guarantee runs 5 years on every kitchen we fit. The measurement that decides everything is the diagonal between the underside of the flight above and the outer edge of the turn below it. We plan the strip-out and the carry as one movement so the kitchen is only out of use for a single day. Old material is stacked outside rather than left along the route.

The grooves sit inside the depth of the top with stone left either side, so a shallow run limits them. The alternative stands on the surface, so the choice is losing worktop permanently or only while you are draining. Where there is no room for a separate drainer, grooves are usually what gets specified instead. Communal heating pipework rises through the flat and is boxed in at floor and at ceiling, and none of it moves for a kitchen. The units stay and only the surface changes, so the job is a day, and what makes it a difficult day is the building. Laminate hides a level that stone will not.