Reception counters and desks in Bankside

Yes. Bankside is on the patch, and the postcodes we work here are SE1. It is worked on our south east London run, along with the rest of Southwark. Building management is often the real gate rather than the bay itself, since the barrier, the shutter and the lift each need someone with a fob. A commercial frontage rarely has anywhere to stop, so the unload is timed rather than assumed and the counter pieces come off first. Two heights, one unload, one trip across the pavement. Both visits happen in your kitchen, the template and the fit, so there is nothing to visit and nothing to collect.

Open-plan living makes the kitchen furniture rather than utility, so the island and the run behind it are nested off the same area of slab. The commercial work in a neighbourhood of new blocks is concierge desks and ground-floor fit-outs: a managed lobby needing a counter that works as a post point and a security position at once, or a shell unit turned into a dental practice or a clinic. A desk seen from a whole floor is finished on every edge. Walls that bow along their length are the normal condition rather than the exception, and a straight-cut back edge will show a shadow gap at one end and touch at the other. A counter is worse off than a kitchen here, because it usually stands clear of the wall and has nothing behind it to hide a gap. Where the plaster bows, the counter is drawn away from it.

Piece length is set by the internal diagonal of the lift car, not by the length of the slab. A counter top is one long piece with no run of cabinets to break it, so the route decides the join count before the sightlines get a vote. Piece length is capped in the drawing office, not on the landing. Time-limited bays are camera-enforced across a lot of managed estates, so the unload runs to the clock and the van moves off afterwards. Loading bays belonging to the building are booked by whoever holds the lease, and that is seldom whoever ordered the counter. The van stays put while the carcass is being scribed to.

Honestly, no, though it would be easy to claim otherwise. What the research on this patch actually lists is worktop fabrication and worktop installation. That says something about the housing round here, not about the work. Quote, cut and fit are the same here as on any other part of the patch. Developer-fitted kitchens come with thin cam-lock carcasses, which are fine under laminate and want bracing before stone goes on them. Counters are nearly always one-offs, so the saving that comes from repeating a specification is not usually on the table here. On a fit-out counter the date is half the decision. Housings and integrated appliances are set out for a 38mm laminate top, so dropping to 20mm or 30mm stone changes the clearances and needs checking before anything is cut. Where an operator is fitting out several receptions, the counters come off one slab run so the desks read as a set rather than as neighbours. Nothing is cut until the joinery has been signed off.

Whether it comes off the same slab as the run behind it or needs one of its own is settled by laying both against the usable area of the slab, not by adding the metres up. A counter has the same argument in miniature: a straight run nests kindly on a slab, and every return costs yield. Every change of plane is a join waiting to be placed well. Reckon on £110 to £550 per square metre for the material supply only, with templating, fabrication and fitting itemised separately.

A run can measure dead right at both ends and still belly out in the middle, which only appears once the template plots the intermediate points. What a counter is scribed to is the joiner's carcass rather than the plaster, which is why it is templated after the carcass is fixed and never before. A shadow gap solves what a scribe cannot. Send the lift car internal dimensions and the loading bay rules with the carcass dimensions, and have the operator mark where the payment terminal and cable grommets really go. A street with houses in single occupation next to the same houses cut into flats produces two completely different jobs from the same elevation. The same split runs through commercial property: a landlord fitting out a shell and a tenant fitting out their own reception want different things from one counter. Dilapidations decide more counter specifications than taste does.

Chips at an edge or a corner are the usual form, because that is where stone is least supported. The workmanship guarantee runs 5 years on every kitchen we fit. Our own installers do the carry, so there is nobody in the middle to argue with about it. A car that takes 2.4m on the diagonal will not take a three-metre worktop however it is stood, and there is no trimming it on the landing. The lower transaction shelf is short and easily handled; it is the upper counter that has to be walked in on edge and turned at every corner. A goods lift diagonal belongs on the counter drawing.

An upstand is a slim strip that follows the worktop up the wall; a full-height splashback runs from the worktop to the underside of the wall units. Ordered later from a different batch, the match is not reliable where the two pieces meet. Tiling and stone can meet, but where they meet is decided before the template rather than after. These buildings have firm rules about what can be propped open, left in a lobby or carried through the residents entrance. The lobby was finished by the developer, so the counter is scribed to stone, terrazzo or a boarded wall somebody else laid, and that face is measured rather than assumed square. Clinic counters carry a card reader and a screen at the low level.

Nothing is measured until the sink, the tap and the hob are in the room to measure against. Between the template and the fit the slab is nested, cut, mitred and dry-assembled on the bench, which is work you never see and is most of the wait. Upstands and splashbacks are templated after the worktop is down and settled, so they are a separate visit. The kitchen is usually part of the living space, so three edges are read from a sofa rather than from standing height at the sink. A reception counter answers to the building it stands in more than to the drawing, because it is fabricated to a carcass somebody else has already built and fixed. The desk is furniture, so all four edges get the same finish.

What changes is the surface. The carcasses underneath stay where they are. Old tops are screwed or glued from underneath, so the drawer boxes come out before the worktop does. The sink and hob are lifted out with the old top and kept aside if you are reusing them. A dedicated loading bay or service yard is the easiest arrangement in a managed building, provided the slot is booked and someone has the key to the shutter. The upper counter is the longest piece on the van, so the tail lift needs the full swing radius clear on the pavement. A red route puts a clock on a counter that will not be rushed.