Skip to content

Hammersmith and Fulham · SW6

Worktop templating in Hurlingham

A digital template plotting the room as it really is, taken once your units are fitted, fixed and level.

Hurlingham kitchens

What the kitchens here are actually like

large detached and semi-detached Victorian houseEdwardian villariverside apartment blockgated modern house

Lath and plaster, a settled floor and a hall with a turn in it are the three things that decide how this job runs. The template records what the building actually did, not what the plan intended, and the gap between those two is what this visit is for. The room as it is, to the millimetre.

Clients regularly ask for a continuous vein match from island to full-height rear panel, which means selecting consecutive slabs from the same block and dry-laying at the yard. The largest houses in Fulham sit here, and the kitchens reflect it - separate prep and pantry areas, a main island of 3-3.6m, an additional run of 4m and often a stone-topped bar or serving unit. Vein-matched book-matched work means the slab selection meeting comes first - once the block is cut you cannot recover a mismatched island end. Some properties back onto the riverside path or club land with no vehicle access at the rear, so the front route is the only one.

The rear extension is frequently original rather than added, which means it is solidly built and just as far out of square as the rest of the house. Alcoves either side of the breast are rarely the same width and rarely parallel, so each one is templated as its own piece with its own scribe. Two to three hours, once the units are in.

The buildings themselves are mostly large detached and semi-detached Victorian house, Edwardian villa, riverside apartment block and gated modern house. Which of those you have decides most of what follows.

True everywhere

Worktop templating, in short

  • Two to three hours on site for a typical kitchen.
  • Units must be fitted, fixed and level first. No stone is ever cut from a plan.
  • Sink, tap and hob must be physically on site, not just ordered.
  • A Belfast or butler sink must be installed and at its final height.

Covered from the New Malden patch. Fitted 3–7 working days from template.

period detached houses and villas

The shape of the run

Seating overhangs past roughly 300mm will not carry on the carcass alone, so flat steel bar or a plywood substrate has to be built into the units first. Join positions and vein direction are marked on the template drawing before it leaves site. Real angles, not plan angles.

period detached houses and villas

What gets asked for here

Honestly, this is not what we do most on this patch. Worktop design & quotation, worktop fabrication and worktop installation come up more often. That is a statement about the local housing rather than about the work, and nothing about how it is quoted, cut or fitted changes because of it.

period detached houses and villas

Getting stone into the room

Driveways and off-street parking are common, which is a rarity in the borough and makes the unload easy, but the houses are deep with long hallways and the kitchen is often the far room past two doorways.

Access

Getting stone into a Hurlingham kitchen

Driveways and off-street parking are common, which is a rarity in the borough and makes the unload easy, but the houses are deep with long hallways and the kitchen is often the far room past two doorways. Some properties back onto the riverside path or club land with no vehicle access at the rear, so the front route is the only one.

Tell us what the approach looks like when you book the template and it gets built into the day rather than discovered on it. Where the route is genuinely tight, it changes how the pieces are cut, which is a fabrication decision rather than a delivery one.

3–7 working days

From template to fitted, working days from template. The same on this patch as every other.

New Malden patch

Hurlingham is worked from our New Malden run, covering South West London & Surrey.

We come to you

Templated in your kitchen, cut in our workshop, fitted by our own installers.

Access told straight

If the route forces an extra join, you hear that at quote stage, not on the day.

Questions

Worktop templating in Hurlingham

If yours is not here, ring and ask. You get a straight answer rather than a call-back from a salesperson.

Do you cover Hurlingham?

Yes. Hurlingham is on the patch, and the postcodes we work here are SW6. It is run from the New Malden side, covering South West London & Surrey. Gravel and block paving both look like hard standing and neither takes a loaded trolley, so the run from tail lift to door gets boarded. A templater circling for a space arrives late into a slot that was already tight, and the drawing is what suffers. It goes on the job sheet for the fitting crew. We template in your kitchen and fit in your kitchen, so there is nothing to visit and nothing to collect.

Does the housing in Hurlingham change how worktop templating works?

Edwardian terraces are wider and taller than the Victorian houses next to them, so the kitchen usually takes a full-width rear room rather than a narrow outrigger. Victorian party walls and chimney-breast returns bow along their length, so the template plots the real line rather than assuming a straight one - the laser picks up points every few hundred millimetres down the back of the run and the drawing carries that curve through to the saw. Recorded as it is, not as it was drawn. Vein-matched book-matched work means the slab selection meeting comes first - once the block is cut you cannot recover a mismatched island end.

How does the stone actually reach a kitchen in Hurlingham?

Driveways and off-street parking are common, which is a rarity in the borough and makes the unload easy, but the houses are deep with long hallways and the kitchen is often the far room past two doorways. Some properties back onto the riverside path or club land with no vehicle access at the rear, so the front route is the only one. A narrow entrance hall with a turn into the back of the house caps the longest piece we can physically get in, whatever the run itself measures. Door widths, turn diagonals and any change of level are recorded on the drawing alongside the run dimensions. It goes on the drawing with the run dimensions. Tell us what the approach looks like when you book the template and it gets built into the day rather than discovered on it.

Do you get much worktop templating work in Hurlingham?

Not particularly, and it would be easy to pretend otherwise. What the research on this patch actually lists is worktop design & quotation, worktop fabrication and worktop installation. That is a statement about the local housing rather than about the work. It is quoted, cut and fitted exactly the same way here as anywhere else on the patch. Extension kitchens are usually specified long before they are buildable, so the run lengths on the drawing and the run lengths in the room are different numbers. The template visit is booked once the units are genuinely in, not when they are nearly in. Units fitted, fixed and level first. Extension kitchens are usually specified long before they are buildable, so the run lengths on the drawing and the run lengths in the room are different numbers. Two to three hours on site, with the sink, tap and hob physically present. Units fitted, fixed and level first.

Why do two Hurlingham kitchens the same size price differently?

An island is a single visible piece with four finished edges and no wall to hide against, so it is the piece the whole kitchen is judged on. The template records every angle in that shape as it actually is rather than as the plan drew it. Real angles, not plan angles. Material is £110-£550 per square metre supply only, and templating, fabrication and fitting are quoted on their own lines.

What has to be finished before you can template?

Where a corner is a couple of degrees off, a mitre cut to a theoretical ninety degrees opens on the wall side and there is no closing it afterwards. One measurement never describes it, which is why a tape reading taken before the visit rarely matches the template. Plotted, not estimated. Units fixed and packed level over the sloping floor, walls replastered and dry at their final thickness (tiling and splashbacks go on after the worktop, never before), and the sink, tap and hob physically on site, with a Belfast sink built in and set at its finished height. Where ownership is split across a building, the common parts belong to someone else and the carry route is negotiated rather than assumed. The templater needs the sink, tap and hob on site, and a Belfast sink installed at its final height. Fitted, fixed and level, then we come.

Next step

Worktop templating in Hurlingham, priced properly

Plans, a sketch or photographs with rough run lengths is enough to start. You get an itemised written quote and the template dates we can offer on this patch.

25-year material warranty and a 5-year workmanship guarantee, both stated on your quote.

+44 7479 194398