Splashbacks and upstands in Wennington

Yes. Wennington is on the patch, and the postcodes we work here are RM13. It is worked on our east London run, along with the rest of Havering. Unrestricted kerbside is straightforward as long as the space in front of the property is actually clear when the van arrives. Panels come off the van in one trip where possible, since a tall piece handled repeatedly is a piece asking to be chipped. Standing a panel on the pavement is the last resort. The template happens in your kitchen and so does the fit, so there is nothing to visit and nothing to collect.

Doorways are low and narrow, which is a genuine constraint on piece length before anything else is considered. These runs are long and often include a range recess, so the splashback is nearly always more than one piece and the joint placement matters, put it in a corner or over a hob centre line, not randomly in the middle of a clear run. Panels expose a wall; upstands forgive one. Where a breast interrupts a long wall the join can often go there, so it reads as a natural break rather than a line in the middle of a worktop. It is usually what pushes a job towards a 100mm upstand instead of a full-height panel, because an upstand rides what a panel exposes. A downstand sets the panel height, not the wall units.

A level threshold with hard standing outside it is the one arrangement where a full run goes in without a single re-grip. Splashback panels are lighter than a worktop and far more awkward, because a tall thin piece has to be carried on edge and cannot be tilted to clear a turn. Nothing is leaned anywhere it could slide down. On a street with no restrictions the constraint is other residents rather than a warden, so it is worth putting a cone or a car out early. Splashbacks are normally the last thing off, so a short parking window is exactly when they get rushed. Handling is where these pieces get damaged.

Not especially, and pretending otherwise would be simple enough. What the research on this patch actually lists is worktop fabrication and worktop installation. It is a fact about the local housing rather than about the work. The job is quoted, cut and fitted the same way wherever on the patch it lands. The junction between the original room and the extension is the point to watch, because the two floors rarely sit at the same height. Splashbacks and upstands are cut from the same slab run at the same time, which is the only way the batch actually matches. The extension electrician finishes after the drawing did. Extension kitchens are usually specified long before they are buildable, so the run lengths on the drawing and the run lengths in the room are different numbers. Ordered later from a different batch, the match is not reliable exactly where the pieces meet. Upstands turn batch offcuts into finished rooms.

Two runs of similar length nest as a pair off one slab, and if one of them grows by a few hundred millimetres the pair stops fitting and the yield changes for both. The same shape decides where splashback pieces break, and a joint in a corner reads as a detail while one in a clear run reads as a mistake. Height is agreed before the cut list closes. Supply-only material is £110 to £550 per square metre, and templating, fabrication and fitting are quoted separately rather than rolled in.

The returns into a breast recess are the tightest scribes in the room, and they are eased in rather than forced. Where the wall cannot be made good, setting the stone deliberately proud on a subframe with a shadow gap reads as a detail rather than a bad fit. Behind the boxing it becomes two pieces. The range and extractor must be sited and the window cill finished before the template, as both fix the vertical limits of the splashback. An owner paying for this directly tends to want the reasoning as much as the number, so a quote that explains why a join sits where it does is worth more than a cheaper one that does not. A 100mm upstand is the low-maintenance answer, and full-height stone is the one that has to be committed to early. Two budgets, settled before anything is cut.

An old stone top is heavier coming out than the new one is going in, and leaves in sections. The sink and hob are lifted out with the old top and kept aside if you are reusing them. A free-parking street with cars both sides can still leave the van forty metres away, and that distance is carry, not driving. Upstands travel in a crate and can wait on the van, which gives some flexibility a full-height panel does not. One trip is always better than three.

Small variation is taken up by packing under the top on the fitting day. Units have to be fixed down as well as levelled. A loose carcass moves under stone. If the carcasses are corrected, the template is taken again, since a drawing off units that then moved is worthless. An alcove is commonly wider at the back than at the front, so a piece cut to the opening drops in and then stands off the rear wall. It decides whether the run gets one continuous piece or a set of separate lengths with a joint at every obstruction. Nothing gets hidden behind a full-height panel.

The alternative stands on the surface, so the choice is losing worktop permanently or only while you are draining. A groove set needs a clear stretch of worktop beside the bowl, so it competes with the run for length instead of being free surface. Retrofitted underfloor heating goes into the new part of the floor and stops at the old part, so the build-up changes partway across the room. What decides between a slim upstand and full-height stone is nearly always the wall rather than the taste. Sockets cut in the shop, not on site.

A sit-on sink and an undermounted one are different cut-outs, so which it is gets settled before the template. The sink, tap and hob have to be physically in the room at the template, not merely ordered, because the cut-out is machined to the item itself. Where the aisle is too tight the usual answer is a reduced-depth top on one side, and a 500mm run is a different cut, a different sink and a different drainer to a 600mm one. Long runs almost never take a single panel, so the joint positions want agreeing before anything is templated. Joint placement is a decision, not an accident.