Worktop replacement in Old Oak and College Park

Yes. Old Oak and College Park is on the patch, and the postcodes we work here are NW10. It is worked on our west London run, along with the rest of Hammersmith and Fulham. Streets near a ground or a venue have restrictions that come and go with the fixture list rather than with the time of day. Waste is the part people forget: the old laminate or tired granite has to be walked back to the van and it does not get lighter. Two carries in one day doubles what the distance costs. The template happens in your kitchen and so does the fit, so there is nothing to visit and nothing to collect.

The bay at the front and the back addition at the rear were built to different standards, and the kitchen is nearly always in the weaker of the two. In most Victorian terraces the kitchen sits in the back addition, so you get a narrow galley with one outside wall and nothing square to work off. Plaster comes away with the old upstands more often than not. Level has to hold across the whole room rather than along one wall, or a floor that falls end to end shows as a step where two pieces meet. The old top has been hiding it, so the first honest look at it happens when the laminate comes off. Nothing about it is a discovery on fitting day.

Carrying through the house means protecting the whole route first: floor boarded, banister padded, and the front door held open on a wedge rather than by hand. Worth remembering that the old tops have to come out the way the new ones come in, and a laminate run is easier to remove in one length than to carry in one. Where it will not come out whole it comes out in sections. On an event day the controls are wider, tighter and enforced harder than the signage suggests on any other morning of the week. We stage the strip-out so the old tops leave in one trip rather than trickling out across the afternoon. A suspension for the full day beats half a day lost.

Yes. On the research for this patch it is the first of the three jobs listed, ahead of worktop installation. Developer-fitted kitchens come with thin cam-lock carcasses, which are fine under laminate and want bracing before stone goes on them. The units stay and only the surface changes, so the whole job is one day rather than a kitchen refit. The annexe top goes in on the same day. Housings and integrated appliances are set out for a 38mm laminate top, so dropping to 20mm or 30mm stone changes the clearances and needs checking before anything is cut. Old tops out in the morning, new stone down and sealed the same afternoon. Booked at short notice, because the notice is short.

A peninsula is an island with one end tied to a run, which means the join between them has to be planned rather than allowed to happen. The existing layout is being kept, so the question is whether the old carcasses will take stone in that shape without more support. Level the units first, measure the shape second. Supply-only material is £110 to £550 per square metre, and templating, fabrication and fitting are quoted separately rather than rolled in.

A floor that falls across the depth of a run rather than along it tips the carcasses front to back, and packing the front feet changes the overhang while it fixes the level. This is the commonest reason a replacement turns out to need more than a straight swap. The laminate was scribed thin. Stone cannot be. Have a plumber booked to disconnect the sink, tap and waste first thing and reconnect after we have gone, and clear the hallway and stairs completely so we can carry slabs through the house. One staircase can serve an owner on the first floor and a managed tenancy on the second, so the access arrangement changes at every landing while the building stays the same. A replacement keeps the units and changes the surface, which is the least disruptive way to do this in an occupied property. Out and in on the same permission.

Grooves are machined in the workshop at the same time as the bowl cut-out, because they cannot be done well in a kitchen. Grooves and an undermounted bowl are usually specified together, since the grooves are run to the bowl edge. Machining is permanent. If a later kitchen moves the sink, the grooves stay where they were cut. The original front door is narrow and the hall is often the only way in, which puts a ceiling on the longest single piece. The units stay and only the surface changes, so the job is a day, and what makes it a difficult day is the building. Cutting the old top out saves the units below it.

Veining carries through a join where both pieces come off the same slab, which is decided at nesting. A join cannot cross a cut-out, so a sink mid-run takes away the position you would have used. A finished join is typically two to three millimetres, colour-matched and sanded flush. The free end is what needs deciding early: square edge, mitred apron down the end, or a full waterfall to the floor, and a waterfall is cut in sequence off the same part of the slab. Old laminate has often been holding a run square for years, and taking it off shows what the units were really doing. The units stay, the surface changes.

The template is taken in your kitchen after the units are in and fixed, never before. The template produces a drawing, and the workshop cuts to that drawing once you agree it. Nothing is measured until the sink, the tap and the hob are in the room to measure against. There is usually a step down into the back addition, so the kitchen floor and the hall floor are not the same level and neither of them is flat. Taking the old tops off is also the first honest look at what has been going on underneath them. Door fronts and drawers get checked against the new thickness.

What moves the figure after templating is a change you make: a different edge, an extra cut-out, a bigger sink chosen late. Every run, cut-out, edge, join and groove set is a line, which is what makes it comparable with anyone else’s. Plumbing, gas and electrical work are not in the figure, because we do not do them. Once the carcasses are levelled the gap under the plinth varies along the run, and that varying gap is the honest record of what the floor is doing. A laminate top was scribed thin at the back to swallow it, and stone cannot be shaved down the same way. What is behind the old top decides the day.