Splashbacks and upstands in Worcester Park

Yes. Worcester Park is on the patch, and the postcodes we work here are KT4. It is worked on our south London run, along with the rest of Sutton. Off-street parking means the van stays put all day, so tools, packers and the offcut we would rather have than not are all within reach. Panels come off the van in one trip where possible, since a tall piece handled repeatedly is a piece asking to be chipped. Panels come across in one pass with the route already cleared. Nothing needs visiting and nothing needs collecting: the template is in your kitchen and so is the fit.

The chimney breast in the corner has usually been left in place, so the run gains a return and two scribed ends. These kitchens are nearly always retiled at least twice, and stripping the old tiles takes the bottom course of plaster with it because the original laminate top ran underneath the tiles rather than up to them. A chimney breast breaks the run and the panels follow it. A live soil stack cannot be chased back into the wall, so the depth it steals is permanent and the run is planned around it rather than through it. It is usually what pushes a job towards a 100mm upstand instead of a full-height panel, because an upstand rides what a panel exposes. A bowed wall shows on a panel and hides under an upstand.

Grass and gravel will not take a loaded trolley, so a boarded track gets laid from the gate to the door before the first piece moves. Splashback panels are lighter than a worktop and far more awkward, because a tall thin piece has to be carried on edge and cannot be tilted to clear a turn. They come in last so nothing is carried past them. A drive that shelves towards the house needs the van chocked and the trolley controlled, since a loaded A-frame gathers speed quickly on a slope. Splashbacks are normally the last thing off, so a short parking window is exactly when they get rushed. A short bay slot is when the tall pieces get damaged.

Not really, and there is no sense dressing it up. What the research on this patch actually lists is worktop installation. That is a statement about the local housing rather than about the work. It gets quoted, cut and fitted exactly as it would anywhere else on the patch. A new extension slab is not automatically level, and that wants checking before templating rather than after the stone is cut. Splashbacks and upstands are cut from the same slab run at the same time, which is the only way the batch actually matches. Wipe-down beats sealed grout on a turnaround. The junction between the original room and the extension is the point to watch, because the two floors rarely sit at the same height. Ordered later from a different batch, the match is not reliable exactly where the pieces meet. Plot spec panels are ordered by the plot, not the room.

Three stools along one side need more clear length than most plans allow, and once the seating depth is fixed the piece either grows or it loses a seat. The same shape decides where splashback pieces break, and a joint in a corner reads as a detail while one in a clear run reads as a mistake. Height is agreed before the cut list closes. Material sits between £110 and £550 per square metre supply only, and templating, fabrication and fitting are quoted line by line.

Boxing built in plasterboard on a light frame will take no useful fixing, so nothing bears on it and the stone is carried off the carcasses either side. A tall panel that fits at the worktop will stand off the wall at the top unless the wall is dubbed out or the panel is scribed. Mitred returns come from one place in the slab. The old tiling must be off and the wall made good and dry before templating, not on fitting day. Someone who expects to still be there in ten years asks different questions: how a honed finish marks, what a sealer does and does not do, and whether a chip by the sink can be repaired in place. A 100mm upstand is the low-maintenance answer, and full-height stone is the one that has to be committed to early. Two attendances need two people to be in.

The template is taken in your kitchen after the units are in and fixed, never before. The same firm templates and fits. Nobody else is brought in to install. Upstands and splashbacks are templated after the worktop is down and settled, so they are a separate visit. Ceilings are lath and plaster at the front and plasterboard in the extension, and the join between the two marks where the original back wall stood. What decides between a slim upstand and full-height stone is nearly always the wall rather than the taste. Same slab run, same day, same batch.

Order is what matters: a slab is templated before it is cut, so an uncut slab is straightforward and one already machined for another kitchen is not. Remnants bought elsewhere are the awkward case, because the drawing is then made to fit the stone. Stone cut to somebody else’s drawing cannot usefully be re-cut to yours. Extension kitchens are usually specified long before they are buildable, so the run lengths on the drawing and the run lengths in the room are different numbers. Socket and switch positions have to be final before templating, because a cut-out in the wrong place means a new piece. One conversion drawing repeats its mistakes six times.

Where there is a lift, whether it can be booked out and padded matters as much as its size. A join forced by the route still sits over a gable, so it is no poorer a join for that. The lift, if there is one, is measured on the diagonal, because that is the dimension a long piece actually uses. A step up to a patio or a raised threshold at the back door means the piece is lifted rather than rolled, and that is where the crew size gets decided. It is usually the full-height panels rather than the tops that will not make the turn, and that only shows up when they arrive. Suction lifters take a panel where hands cannot get a grip.

If it is a decision for later, say so at the template: the match is a question about the batch. Both are templated after the worktop is down and settled, because they are cut to the wall itself. Tiling and stone can meet, but where they meet is decided before the template rather than after. These kitchens have been retiled at least twice, and stripping the tiles takes the bottom band of plaster with them because the old laminate ran underneath rather than up to them. That leaves a ragged band right where the upstand has to sit, which is fine for a 100mm upstand that covers it, but a full-height splashback needs the wall made good first or it will rock on the high spots. Where the plaster undulates, the shorter piece wins.