Splashbacks and upstands in Cheapside

Yes. Cheapside is on the patch, and the postcodes we work here are EC2V. It is worked on our City of London run, along with the rest of the Square Mile. Underground loading has a height restriction, and a van with an A-frame on it is taller than the driver remembers. Panels come off the van in one trip where possible, since a tall piece handled repeatedly is a piece asking to be chipped. Handling is where these pieces get damaged. Template and fit both happen at the property, so there is nothing to drive to and nothing to collect.

The flat entrance door and the internal doorways are usually tighter than the communal stairs, which is the opposite of what most people assume. Lath-and-plaster on the party wall and the chimney breast returns almost never runs true, so a 100mm upstand bedded on silicone is the honest answer here, it rides the bow and hides the junction the worktop can never close on its own. Height, returns and sockets, all settled on site. Where a column lands in the run the template plots its actual outline so the stone is cut to fit around it rather than stopped short and filled. A tall panel that fits at the worktop will stand off the wall at the top unless the wall is dubbed out or the panel is scribed. A breast return is scribed on three edges.

Where the van stands level with the front of the house a piece gets handled twice instead of five times, and stone breaks on handling rather than on the road. Splashback panels are lighter than a worktop and far more awkward, because a tall thin piece has to be carried on edge and cannot be tilted to clear a turn. They stand upright in the van and stay upright until they are on the wall. Where the bay sits some distance from the core, the carry across the car park is the longest leg of the day and gets boarded and lit. Upstands travel in a crate and can wait on the van, which gives some flexibility a full-height panel does not. One trip is always better than three.

Honestly, no, though it would be easy to claim otherwise. What the research on this patch actually lists is worktop replacement and worktop installation. That says something about the housing round here, not about the work. Quote, cut and fit are the same here as on any other part of the patch. Where a single building holds several small kitchens, the work arrives as one job rather than four, and it should be cut off the same slab run so the batches genuinely match. Splashbacks and upstands are cut from the same slab run at the same time, which is the only way the batch actually matches. Cut now, stored for the next void. Small kitchens in a shared house are all short runs and tight cut-out spacing, which is more bench work per square metre than one large kitchen would be. Ordered later from a different batch, the match is not reliable exactly where the pieces meet. Same batch, or the join will say so.

The free end is what needs deciding early: square edge, mitred apron down the end, or a full waterfall to the floor, and a waterfall is cut in sequence off the same part of the slab. Long runs almost never take a single panel, so the joint positions want agreeing before anything is templated. The hob panel is sized after the extractor, not before. Reckon on £110 to £550 per square metre for the material supply only, with templating, fabrication and fitting itemised separately.

Exposed structure means the back edge is not a straight line at all, and a scribe of fifteen or twenty millimetres across a run is normal. Where the wall cannot be made good, setting the stone deliberately proud on a subframe with a shadow gap reads as a detail rather than a bad fit. Set it proud on a subframe and the gap becomes deliberate. The chimney breast recess must be replastered and fully dry, and the hob and extractor positions fixed, before anyone templates a full-height piece into it. One staircase can serve an owner on the first floor and a managed tenancy on the second, so the access arrangement changes at every landing while the building stays the same. A 100mm upstand is the low-maintenance answer, and full-height stone is the one that has to be committed to early. An owner can wait for it; a void period cannot.

Upkeep is settled when the slab is chosen, since it belongs to the material rather than the fabrication. Quartz carries resin, so a hot pan wants a trivet, while granite and sintered stone will take one without complaint. Where a top takes wine, oil and lemon most days, the non-porous materials ask least of the household. Cornice, picture rails and deep skirting survive in converted rooms, so the run stands off the wall and the back edge follows the units rather than the plaster. Where a client wants a full-height piece behind the hob, it usually sits in the old chimney recess, and that recess is rarely square top to bottom or side to side, so it has to be templated as a trapezium rather than a rectangle. A hundred millimetres covers more than it looks.

The workmanship guarantee runs 5 years on every kitchen we fit. A remake goes back through the same cutting and polishing, so it is a return visit rather than a patch. Our own installers do the carry, so there is nobody in the middle to argue with about it. Even an easy kerbside carry wants the pavement clear at the tail lift, because a three-metre piece on edge has a swing radius nobody expects until it is swinging. It is usually the full-height panels rather than the tops that will not make the turn, and that only shows up when they arrive. A door frame catches a tall panel long before a short one.

A long top on units that were shimmed once and never checked is the commonest version of this, and it is cheap to fix beforehand. Variation past what packing can take up has to be corrected in the carcasses before we cut, because the template records the units as they stand. A deep scribe comes out of the nest, so how far the stone has to be relieved changes which part of the slab the piece is cut from. It decides whether the run gets one continuous piece or a set of separate lengths with a joint at every obstruction. An upstand rides what a panel exposes.

Upstand or splashback, the stone is cut from the same slab run as the worktop, at the same time, so the batch actually matches. An upstand is a slim strip that follows the worktop up the wall; a full-height splashback runs from the worktop to the underside of the wall units. Lease conditions and the other flats in the building decide when noisy work can happen, so the fitting day has a start and a finish that are not ours to set. A 100mm upstand bedded on silicone is the honest answer where the plaster bows, because it rides what a tall panel exposes. The plaster behind it is the real question.