Blog · Planning and process

How level do kitchen units have to be for a stone worktop, and whose job is it

Level to within a millimetre along each run, checked across the whole run rather than unit by unit. Here is why stone is unforgiving about it, and whose contractual job it is.

Karem AltaisnahFounder and director, Worktop Worx Ltd10 min read

A compact U-shaped kitchen with light grey handleless units, white sparkle quartz worktops and a peninsula breakfast bar with an inset sink and induction hob.

This question gets asked constantly on trade forums and almost never gets answered for the person who needs it. Fitters answer each other in shorthand ("as level as you can get them", "shim it") which tells a homeowner nothing about what tolerance applies, how it is measured, or who is contractually on the hook when it is wrong. So here is the number, the method, and the scope boundary, written down in the order you will actually need them.

01 / 06

The answer, in one line

The short answer

  • Level to within 1mm along each run, with no high points. That is the standard published by UK stone fabricators and it is the one we check against.
  • It is checked across the whole run with a long level, not unit by unit with a short one. Four individually level units can still form a run that is 4mm out.
  • We do not level units. That is the kitchen fitter’s scope. We check on arrival and we will not template or fit on a run that is out.

One UK fabricator publishes the requirement in exactly those words on its own pre-template page: the units should be level to within a millimetre along each run, with no high points. Another sets out the same requirement less numerically. All base units fitted, secured to the wall and to each other, end panels on, units level. It is not a competitive standard that firms differ on. It is what the material demands, and the fabricators who publish it are describing physics rather than policy.

A millimetre sounds punishing until you understand what it is protecting. It is not about the worktop looking wonky. It is about where the load goes.

02 / 06

How it is actually checked

The common mistake is levelling each unit in turn. A fitter sets a 600mm cabinet, puts a 600mm level across the top, adjusts the legs until the bubble sits central, and moves on. Do that four times along a 2.4m run and you can end up with four level cabinets whose tops describe a shallow curve, because each one was levelled against itself rather than against the run.

The check that matters is a long spirit level, 1.8m or 2m, laid along the whole run, then across it front to back at several points, then diagonally across a corner where two runs meet. What you are looking for is not just tilt but the high point: the single cabinet that stands proud of its neighbours. A dip can be packed. A high point cannot be, because everything else has to come up to meet it.

  • Along the run, end to end, with the longest level that fits. This is the one that finds the curve.
  • Front to back on each cabinet, because a run can be dead level lengthways and still tip forward.
  • Across the internal corner of an L, where two runs that are each level can still meet at different heights.
  • Across the join positions specifically, because a step at a join is the defect people notice for the next fifteen years.
  • Under any run where the floor changes, a doorway threshold, an old chimney breast, a levelling screed that stopped short.

03 / 06

Why stone is unforgiving about it

A laminate worktop is a flexible board on a fixed substrate. Lay it over a run that dips 3mm in the middle and it will follow the dip, and nobody will ever know. Stone does not follow anything. A quartz or granite slab is rigid and, in the plane it is weakest in, brittle. Put it on a run with a high point and it does not curve over the high point. It bridges the two ends and bears on the middle, and now the whole weight of the piece plus everything you put on it is concentrated on a single cabinet gable.

That is where cracks start, and they almost never start where the load is. They start at the weakest geometry nearest the stress, which in most kitchens is the internal corner of the sink or hob cut-out. A hairline that appears three weeks after installation, running out of a cut-out corner at an angle, is very rarely a material fault. It is a support fault that took three weeks to find its way to the surface.

The temptation, in the moment, is to pack the low points with shims and get the job done. We will not do it, and the reason is that shimming converts a continuous bearing into a series of point loads. Instead of the slab sitting on a plane, it now sits on four or five hard spots with air between them. That is a worse condition than the one you started with, and it is the specific reason a shimmed slab is a cracked slab more often than an unshimmed one on a level run. Packing is legitimate for a millimetre of make-up across a full-width batten. It is not a substitute for levelling the carcasses.

White veined breakfast bar with four grey velvet stools in a pale grey handleless kitchen
A peninsula like this is bearing on the units under it and cantilevering past them. Everything about how long it lasts is decided by whether the run beneath was level before the stone arrived.

04 / 06

Whose job it is, said plainly

Levelling and fixing base units is kitchen-fitting work. It is not worktop work, we do not quote for it, and we do not carry it out on the day as a favour, because a favour on Tuesday becomes a liability in March. What we do instead is check, and act on what we find.

TaskWhose scopeWhat we do about it
Assemble and position base unitsKitchen fitterNothing. We arrive after this is done.
Level the run and fix units to wall and to each otherKitchen fitterWe check it on arrival with a long level, before anything else.
Fit end panels, decor panels and support panelsKitchen fitterWe check these are on, because they change the finished dimension.
Decide whether the run is fit to templateUsIf it is out, we say so, and we do not template. The template would be a copy of a kitchen you are about to change.
Decide whether the run is fit to fit stone onUsIf it has moved since the template, we stop. Fitting a rigid slab to a run we know is out is not a compromise we are willing to make.
Support for an overhang, island or breakfast barSharedWe specify what the stone needs. Installing brackets or a substructure is joinery, and it must be in before we arrive.
The scope boundary, published rather than buried in terms and conditions.

People sometimes read that as unhelpful. It is the opposite. A firm that will template anything put in front of it is a firm that has decided the argument happens later, when there is a slab in the room and a deposit spent. Refusing at the survey stage costs you a rebooked visit. Refusing at the fitting stage costs you a remake. Where this sits in the wider programme is set out in the order a kitchen actually goes in, and the full list of everything else that must be true on the day is what has to be ready before we template.

05 / 06

What it looks like when nobody checks

There is a case study of this on a UK consumer forum, posted on 1 December 2024, and it is worth reading in full because the chronology is textbook. We are not naming any of the businesses involved and the point is not who they were, the point is the shape of the failure, which repeats.

“The fitter doesnt check for level cabinet and attempts to install worktops.”

The opening post of a MoneySavingExpert thread, 1 December 2024

From there it unwinds exactly as you would expect. The original installation date is lost to illness. The fitter attends on 6 November, does not check level, attempts the installation anyway, and the joins are afterwards deemed to have failed. He attends again on 22 November; the kitchen fitter levels the cabinets that morning and has them done by half past ten; the worktop fitter decides it is too late in the day to proceed and rebooks to Saturday 30 November. On the 30th he does not turn up. By then the worktops are in pieces, the manufacturer has entered administration, and the customer had paid by bank transfer, which (as another contributor points out in the thread) leaves no Section 75 protection to fall back on.

Days lost in one documented case

  • Original date to first attempt9 days
  • First attempt to second attempt16 days
  • Second attempt to the no-show8 days
Counted from the dates the poster gives in that thread. Thirty-three days from the original installation date to a fitter who did not arrive. All of it downstream of one check that was not made.

The most quoted reply in that thread makes the argument better than we can: the fitter should not have been called to site until the site was ready. That is a criticism of the coordination, not of the customer, and it lands on whoever owns the programme. In a kitchen where one firm does both worktop visits, that is us, and it is why we would rather have an awkward conversation in week one than a legal one in week eight.

06 / 06

The conversation to have with your kitchen fitter before they start

Almost every version of this problem is solved by four sentences said at the right time. Say them before the units go in, not after.

  1. "The worktop is stone, not laminate."

    This changes how a good fitter works. It means the run gets levelled to a stone tolerance rather than a laminate one, it means no reliance on the worktop to hide a discrepancy, and it means end panels and support panels have to be finished rather than left to be trimmed later.

  2. "Please level along the whole run with a long level, not cabinet by cabinet."

    Most fitters do this anyway. The ones who do not are usually working quickly on a laminate assumption, and asking costs you nothing.

  3. "Will the run be finished, fixed and level by the date of the template?"

    Get a date, not a reassurance. Then give that date to the worktop company, and give it as the date the kitchen will be ready rather than the date the fitter hopes to finish.

  4. "Who is levelling the island, and what is going under the overhang?"

    Islands are where this goes wrong most often, because they are freestanding, they sit on a floor that may not be flat, and the overhang needs a substructure that somebody has to install before the stone turns up.

01

My units are 2mm out over three metres. Is that really a problem?

Over a straight run with no join and no cut-out near the discrepancy, often not. It depends where the 2mm is and whether it is a dip or a high point. Over a run with a join in the middle of it, yes, because a step at a join is both a visible defect and a stress concentration. Ask for it to be corrected rather than assuming somebody will make it work.

02

Can you not just pack it with shims on the day?

We will not, and you should be cautious of anyone who offers to. Packing turns a continuous bearing into a handful of point loads, which is the condition stone is least tolerant of. Where a millimetre of make-up is genuinely needed we use a continuous full-width batten, not spot packers.

03

What if you find the run is out when you arrive to template?

We tell you on the spot, show you on the level, and rebook. Nothing is cut and no slab is committed at that stage, so the cost is a diary slot rather than a piece of stone. It is the cheapest possible moment for this to be discovered, and it is one of the reasons what templating actually is matters more than people expect.

04

The worktop is already on and the units were never level. Can it be lifted and redone?

Sometimes. Lifting a bonded stone worktop to realign the carcasses beneath is a real job that is done, but the risk of breaking a piece sits with whoever lifts it, and undermount sinks and joins usually have to be broken and remade. Get the assessment in writing before anybody puts a hand under it, and next time, work through what to check on fitting day before the fitters leave rather than after.

05

Does thicker stone forgive an out-of-level run?

No. A 30mm slab is stiffer than a 20mm one, which means it bridges a dip more confidently and concentrates the load more sharply on the high point. Thickness changes the failure mode, not the requirement.

What to take away

  • The published standard across UK stone fabricators is level to within 1mm along each run, with no high points. That is what we check against on arrival.
  • Check across the whole run with a long level, not unit by unit. Four individually level cabinets can still form a curved run.
  • High points are the danger, not dips. A rigid slab bridges the ends and bears on the middle, and cracks start at the nearest cut-out corner.
  • Levelling units is the kitchen fitter’s scope. We do not do it, we do not shim around it, and we will not template or fit on a run that is out.
  • Say four sentences to your kitchen fitter before the units go in (starting with "the worktop is stone, not laminate"), and most of this problem disappears.

Sources

Every figure quoted above is traceable to one of these. Where a source is a price survey rather than our own quoting, it is named as such in the text.

  1. [1]Is My Kitchen Ready For Template?, published levelling tolerance for stone worktops, Affordable Granite, retrieved 25 August 2026
  2. [2]Template and Installation Guidelines, base unit and preparation requirements, UK Stone Worktops, retrieved 25 August 2026
  3. [3]Big trouble with worktop installation, the 1 December 2024 chronology, MoneySavingExpert, retrieved 25 August 2026
  4. [4]Opinions on worktop installation, DIYnot, retrieved 25 August 2026
  5. [5]Worktop installation, templates?, DIYnot, retrieved 25 August 2026

Start your free quote

Tell us where the kitchen is and we will take it from there. A person reads every request and sends a written, itemised quote.