Worktops in East Dulwich

Yes. East Dulwich is on the patch, and the postcodes we work here are SE22. It is worked on our south east London run, along with the rest of Southwark. A suspension is charged by the bay and by the day, so the number of metres asked for is worth getting right the first time. Whatever the standing allows, the stone leaves that van finished, because every edge, cut-out and internal radius is machined at the works and none of it is open to reconsideration at the kerb. Dry cutting quartz burns the resin and the burn does not polish out. The template happens in your kitchen and so does the fit, so there is nothing to visit and nothing to collect.

The outrigger shares a party wall with the addition next door for its whole length, so one long side of the kitchen is solid brick with another kitchen on the far side of it. The kitchen in one of these sits in the back addition and takes its daylight from one end, so the working half of the run is the darker half and a pale stone with a honed or matt face does more there than any colour with depth in it. Cool artificial light turns a warm stone grey. Casement handles and stays swing down into the space above the worktop, so the clearance that counts is the one measured with the window open. Every notch and every scribe is machined into the piece before it leaves the works, and a hard sintered surface is the least forgiving of a tight internal corner, so one is always cut with a generous radius. Heat at the lip of an opening is the slow kind of damage.

Spindles and a newel cap stand proud of the string, so the usable width on a turn is measured to the handrail rather than to the wall behind it. That caps the longest piece, and a run split into two lengths nests differently on the slab, which moves the yield and moves the figure with it. Every extra seam buys two more polished edges and a resin match. Plenty of zones run at the weekend as well as through the week, so a Saturday date is not automatically the easier one to work. A granite kitchen ends its day with a sealer, and a sealer wants a dry face and a quiet hour afterwards, so that hour is written into the day rather than borrowed from it. A honed face marks on grit, so nothing is set down bare.

Not really, and claiming otherwise would cost nothing and mean nothing. What the research on this patch actually lists is worktop fabrication and worktop installation. It reflects the local housing rather than any difference in the work. It is quoted, cut and fitted here the same way it is anywhere else on the patch. Extension kitchens are usually specified long before they are buildable, so the run lengths on the drawing and the run lengths in the room are different numbers. Where several kitchens are ordered together the sensible move is to take them all off one batch, because two slabs of the same name bought six months apart will not sit happily in the same building. Fitting follows template by five to ten working days. Extension work runs late far more often than it runs early, and the worktop is close to the last thing in, so the date agreed at the start is rarely the date that happens. Adding an island is what moves most of these projects from one slab to two, and that jump is the single largest step in any worktop quotation. Four samples by post settle more than four showroom visits.

One leg of an L is nearly always the working run and the other little more than a landing space, but both are templated, cut and edged to the same standard. A shape like that nests kindly on a slab, so more of what gets bought ends up on the units and the rate per square metre behaves much as the brochure says it will. Edge metreage climbs with corners, not with floor area. Supply only, material is £110 to £550 per square metre, with templating, fabrication and fitting quoted on their own lines.

A low sill over the sink run is what decides between an upstand and stone dying into a window board, and there is often less clearance than an upstand is tall. A hob dropped into the middle of a length puts sustained warmth at the lip of a cut-out, and an engineered surface will yellow there across ten years where a natural one takes it without comment. The obstruction is templated as found and cut as templated. Send the run lengths, say where the sink and hob will sit, and tell us which way the room faces and what lighting is going in above the working run. Two flats with an identical layout can want entirely different things from the same run of worktop, which is why the quote follows the run rather than the address. That changes which questions are worth asking about the stone, because somebody staying put wants to know how a honed face marks in five years and somebody selling wants to know how it photographs next spring. The middle band is where most fitted surfaces honestly sit.

On a replacement the old top comes off in the morning and the new stone is down and sealed the same day. Tiling bonded to the wall behind usually comes away with the old top, so that wall is agreed beforehand. The units stay where they are and only the surface changes. A permit covering the street is permission to park rather than a space reserved on it, and on a full street the difference is the whole morning. Sintered surfaces are the hardest of the three to machine and the messiest to cut wet, which is precisely why none of that happens on a public pavement. The last hour on a granite kitchen belongs to the sealer.

A tap under a window board still needs room for its handle to lift, which is checked at the template. Two bowls means two cut-outs and a bridge of stone between them, which decides where the sink can go. Nothing is cut out in the kitchen. Cutting a bowl on site is how worktops get cracked. Two runs meeting at an internal corner is the most common shape we fit, and the corner is where the decisions are. An island is the piece that decides whether one slab covers the kitchen or two, and a second slab arrives as a step in the figure rather than a gentle slope. A pale honed face earns its keep in a room short of daylight.

The template produces a drawing, and the workshop cuts to that drawing once you agree it. Upstands and splashbacks are templated after the worktop is down and settled, so they are a separate visit. The template is taken in your kitchen after the units are in and fixed, never before. Original quarry tile is often still down under two or three later floor coverings, which is why the finished floor height is rarely what anyone expects. Which stone belongs on top of all that is a separate question from the building itself, and it is the one with a figure attached, because supply alone runs from £110 to £550 per square metre before a single cut has been made. Supply is a range, and the room decides where in it you land.

The alternative to a join is a shorter run, which is usually the wrong thing to trade away. The lift, if there is one, is measured on the diagonal, because that is the dimension a long piece actually uses. A piece travels on edge, never flat, because on edge is how stone of that length carries its own weight. The top step is rarely the end of it, because a door swinging out onto the landing has to be held back before a piece can come off the flight. Where a seam becomes unavoidable the choice of stone starts to matter, because a fine even speckle closes a joint almost invisibly and a broad vein simply will not. The route rewrites the cut list, and the cut list is the price.