Worktops in Green Street

Yes. Green Street is on the patch, and the postcodes we work here are E7, E13. It is worked on our east London run, along with the rest of Newham. A bus lane along the frontage brings its own hours with it, and stopping in one is enforced the same way the red route is. Whatever the standing allows, the stone leaves that van finished, because every edge, cut-out and internal radius is machined at the works and none of it is open to reconsideration at the kerb. Dry cutting quartz burns the resin and the burn does not polish out. There is nothing to drive to and nothing to pick up, because both visits are to the property itself.

A flat over a shop is reached by a separate street door and a straight steep stair, and that stair is the whole access question. These kitchens are small and roughly square, so the run is short, the join count is low and the material band accounts for almost all of the figure rather than the bench time. Honed hides the dust an older house makes all year. Two walls each a degree out give an internal corner two degrees out, and the whole of that error lands in the mitre. Every notch and every scribe is machined into the piece before it leaves the works, and a hard sintered surface is the least forgiving of a tight internal corner, so one is always cut with a generous radius. A tight inside corner is where brittle material gives up.

Open-tread and cantilevered stairs give nothing to lean a piece against, so the whole weight stays on the crew for the full length of the flight. That caps the longest piece, and a run split into two lengths nests differently on the slab, which moves the yield and moves the figure with it. Speckle forgives a joint that a sweeping figure never would. The van is not staying on a main road for the day, so once the stone is off it goes and parks properly somewhere else. A granite kitchen ends its day with a sealer, and a sealer wants a dry face and a quiet hour afterwards, so that hour is written into the day rather than borrowed from it. A honed face marks on grit, so nothing is set down bare.

Honestly, no, though it would be easy to claim otherwise. What the research on this patch actually lists is worktop replacement and worktop splashbacks & upstands. That says something about the housing round here, not about the work. Quote, cut and fit are the same here as on any other part of the patch. Where several adults share the cooking the kitchen is in use most of the day, so a fitting slot has to be agreed with more people than usual. Where several kitchens are ordered together the sensible move is to take them all off one batch, because two slabs of the same name bought six months apart will not sit happily in the same building. Where the cooking is serious, heat tolerance leads the list. Households sharing a house tend to want two prep areas rather than one, which usually means an island as well as a perimeter run. Volume work tends to live at the entry end of the range, and the entry end is genuine stone rather than a compromise, since the lowest supply figure we quote is a sintered surface and not a thin laminate pretending to be one. Order the stone against the room, never against the drawing.

The walkway between the two runs is fixed by the units either side, so any overhang added to one worktop comes straight off the space somebody has to stand in. A shape like that nests kindly on a slab, so more of what gets bought ends up on the units and the rate per square metre behaves much as the brochure says it will. Two mitres and three lengths is bench work, not surface area. Reckon on £110 to £550 per square metre for the material supply only, with templating, fabrication and fitting itemised separately.

A scribe has a working limit, and past twenty millimetres or so the back edge starts eating depth the run cannot spare. A hob dropped into the middle of a length puts sustained warmth at the lip of a cut-out, and an engineered surface will yellow there across ten years where a natural one takes it without comment. The wall decides the scribe and the scribe decides the depth. Measure the run between the walls, note the cill height above the units, and tell us the thickness of the top that is coming off. Whoever manages the block controls the lift booking, the bin store and the visitor parking, and none of that sits in the gift of the household whose kitchen it is. That changes which questions are worth asking about the stone, because somebody staying put wants to know how a honed face marks in five years and somebody selling wants to know how it photographs next spring. A chip in natural stone can be filled and polished in place.

Variation past what packing can take up has to be corrected in the carcasses before we cut, because the template records the units as they stand. The check comes before the measuring rather than after, because the whole drawing is set out from that plane. Packing takes up small variation. It is not there to hide something that belongs in the units. Walls that bow along their length are the normal condition rather than the exception, and a straight-cut back edge will show a shadow gap at one end and touch at the other. A run that sits under strong sun for hours every afternoon suits a surface built to be stable in daylight, because a resin-bound stone is made for indoor use and sustained sunlight is the one thing it was never designed around. Sealing suits stone that drinks; nothing else needs it.

Stone cut to somebody else’s drawing cannot usefully be re-cut to yours. Delivery to the workshop has to be arranged and dated, since nothing is nested until it is there. Supply through us runs £110 to £550 per square metre for the slab alone, which is the line you would be removing. A second kitchen or a kitchenette in an annexe is a small job with the same fixed template, fabrication and fitting lines as a large one. Adding an island is what moves most of these projects from one slab to two, and that jump is the single largest step in any worktop quotation. Several kitchens at once should come off a single batch.

Hoisting through a window is occasionally the answer, and it is a decision made at the template, not improvised on the fitting day. An external stair, a side return or a rear garden counts as carry and is measured the same way. The lift, if there is one, is measured on the diagonal, because that is the dimension a long piece actually uses. A handrail that has to come off before a piece will pass is twenty minutes at the start of the day, and it goes back on the wall before we leave. Where a seam becomes unavoidable the choice of stone starts to matter, because a fine even speckle closes a joint almost invisibly and a broad vein simply will not. No colour and no edge is adjustable once a piece is machined.

An upstand is a slim strip that follows the worktop up the wall; a full-height splashback runs from the worktop to the underside of the wall units. A full-height piece behind the hob has to allow for the extractor, so that gets settled first. Tiling and stone can meet, but where they meet is decided before the template rather than after. The stair from the street is narrow with a tight turn at the top, which caps piece length well below anything the run itself needs. Coming off a thick laminate top changes the front edge, and twenty millimetres reads closer to what the room is used to than thirty does against existing tiling and a window board. Seen from both sides, the figure has to run continuously.