Worktops in Muswell Hill

Yes. Muswell Hill is on the patch, and the postcodes we work here are N10. It is worked on our north London run, along with the rest of Haringey. Where the nearest legal space is a couple of streets back, the walk with each piece becomes the job, and the crew is sized for walking rather than wheeling. Whatever the standing allows, the stone leaves that van finished, because every edge, cut-out and internal radius is machined at the works and none of it is open to reconsideration at the kerb. The face is uncovered once, and that once is at handover. Template and fit both happen at the property, so there is nothing to drive to and nothing to collect.

The rear wall is usually a single brick thick and has been rendered, patched and re-rendered, so it bows in and out along the length of the run. The kitchen in one of these sits in the back addition and takes its daylight from one end, so the working half of the run is the darker half and a pale stone with a honed or matt face does more there than any colour with depth in it. Plain stone takes the seam that a long carry forces. Two walls each a degree out give an internal corner two degrees out, and the whole of that error lands in the mitre. Every notch and every scribe is machined into the piece before it leaves the works, and a hard sintered surface is the least forgiving of a tight internal corner, so one is always cut with a generous radius. A deep scribe moves the pattern back along with the depth.

There is no leaning a piece against a wall halfway up, so any flight longer than a dozen treads is planned around a rest point on a landing. That caps the longest piece, and a run split into two lengths nests differently on the slab, which moves the yield and moves the figure with it. The way in caps the piece, and the slab layout follows the cap. Applying for a suspension means naming a length of kerb and a date, and moving the date generally means applying for it again. A granite kitchen ends its day with a sealer, and a sealer wants a dry face and a quiet hour afterwards, so that hour is written into the day rather than borrowed from it. Stone arrives finished, because a kerb is not a polishing shop.

Honestly, no, though it would be easy to claim otherwise. What the research on this patch actually lists is worktop installation. That says something about the housing round here, not about the work. Quote, cut and fit are the same here as on any other part of the patch. The junction between the original room and the extension is the point to watch, because the two floors rarely sit at the same height. Volume work tends to live at the entry end of the range, and the entry end is genuine stone rather than a compromise, since the lowest supply figure we quote is a sintered surface and not a thin laminate pretending to be one. Buying for hard use is a different exercise from buying for looks. Extension kitchens are usually specified long before they are buildable, so the run lengths on the drawing and the run lengths in the room are different numbers. Adding an island is what moves most of these projects from one slab to two, and that jump is the single largest step in any worktop quotation. The remainder of a slab is bought whether it is fitted or not.

Seating overhangs past roughly 300mm will not carry on the carcass alone, so flat steel bar or a plywood substrate has to be built into the units first. A shape like that nests kindly on a slab, so more of what gets bought ends up on the units and the rate per square metre behaves much as the brochure says it will. Cut-outs take material out of the piece that carries the sink. Reckon on £110 to £550 per square metre for the material supply only, with templating, fabrication and fitting itemised separately.

A scribe has a working limit, and past twenty millimetres or so the back edge starts eating depth the run cannot spare. A hob dropped into the middle of a length puts sustained warmth at the lip of a cut-out, and an engineered surface will yellow there across ten years where a natural one takes it without comment. Thirty millimetres bridges a gap that twenty millimetres will not. Send the run lengths, say where the sink and hob will sit, and tell us which way the room faces and what lighting is going in above the working run. Mixed ownership means the decision-maker is not always the person who lets us in, so it is worth being clear early about who signs the quote off. That changes which questions are worth asking about the stone, because somebody staying put wants to know how a honed face marks in five years and somebody selling wants to know how it photographs next spring. Sealing is a job somebody has to want to do each year.

Packing takes up small variation. It is not there to hide something that belongs in the units. A long top on units that were shimmed once and never checked is the commonest version of this, and it is cheap to fix beforehand. Variation past what packing can take up has to be corrected in the carcasses before we cut, because the template records the units as they stand. Walls that bow along their length are the normal condition rather than the exception, and a straight-cut back edge will show a shadow gap at one end and touch at the other. A run that sits under strong sun for hours every afternoon suits a surface built to be stable in daylight, because a resin-bound stone is made for indoor use and sustained sunlight is the one thing it was never designed around. A cranked piece eats more slab than the two straights it replaces.

An upstand is a slim strip that follows the worktop up the wall; a full-height splashback runs from the worktop to the underside of the wall units. Tiling and stone can meet, but where they meet is decided before the template rather than after. An upstand covers the gap where the worktop meets a wall that is not flat, which is its real job. Deep original skirting is often left in behind the units, standing them off the wall, so the back edge of the stone is plotted where the carcasses actually sit. Alcoves either side of the old breast chop the run into short lengths, and a kitchen made of short lengths is the case where buying a slab outright beats buying the square metres, because the remainder is paid for in both. Hard-working kitchens suit surfaces that ask for nothing.

A Belfast or butler sink has to be installed and at its final height before the template, because the stone is cut to sit on it. A piece with a bowl and a hob cut into it is the fragile one, and it is handled accordingly. If the sink or hob changes after the template, the drawing changes first and nothing is cut meanwhile. An island carries its own edge detail all the way round, so a mitred 100mm apron on four sides is four mitres cut, bonded and polished before the piece ever leaves the bench. An island is the piece that decides whether one slab covers the kitchen or two, and a second slab arrives as a step in the figure rather than a gentle slope. Extra depth sounds free and frequently buys another slab.

A dropped pan years later is a different question, and stone is remade rather than filled either way. Stone cannot be filled and made good the way laminate can, so a damaged piece is remade rather than patched. Every piece is dry-assembled on the bench before it is loaded, so a fabrication mistake is found in the workshop rather than in your kitchen. Pendant fittings over the stairwell and anything hung on the half-landing come down first, because a piece on edge sweeps a wider arc than the people carrying it. Where a seam becomes unavoidable the choice of stone starts to matter, because a fine even speckle closes a joint almost invisibly and a broad vein simply will not. A forced seam is a material decision before it is a fitting one.