Worktops in Sudbury

Yes. Sudbury is on the patch, and the postcodes we work here are HA0. It is worked on our north west London run, along with the rest of Brent. A step up from the drive to the threshold turns the last two metres into a lift, and a lift is where two pairs of hands become the minimum. Whatever the standing allows, the stone leaves that van finished, because every edge, cut-out and internal radius is machined at the works and none of it is open to reconsideration at the kerb. Colour matched resin is mixed to the slab, not to a chart. We template in your kitchen and fit in your kitchen, so there is nothing to visit and nothing to collect.

The stairs come down against the wall the addition opens off, so the doorway into the kitchen is offset and the corner beside it is taken by the cupboard under the flight. The kitchen in one of these sits in the back addition and takes its daylight from one end, so the working half of the run is the darker half and a pale stone with a honed or matt face does more there than any colour with depth in it. Long narrow rooms want a pale face at the working end. A run can measure dead right at both ends and still belly out in the middle, which only appears once the template plots the intermediate points. Every notch and every scribe is machined into the piece before it leaves the works, and a hard sintered surface is the least forgiving of a tight internal corner, so one is always cut with a generous radius. Reach across an unsupported span is a thickness question.

Suction lifters need a clean dry face to hold, so in the wet the pads come off and the piece goes back to being carried on webbing by hand. That caps the longest piece, and a run split into two lengths nests differently on the slab, which moves the yield and moves the figure with it. Short pieces nest tighter, and tighter nesting is less stone bought. Where the van cannot turn on the plot it has to arrive already facing the right way, so the approach along the street is part of the plan. A granite kitchen ends its day with a sealer, and a sealer wants a dry face and a quiet hour afterwards, so that hour is written into the day rather than borrowed from it. Thirty millimetre stone unloads slowly and thin stone does not.

Not really, and there is no sense dressing it up. What the research on this patch actually lists is worktop replacement and worktop installation. That is a statement about the local housing rather than about the work. It gets quoted, cut and fitted exactly as it would anywhere else on the patch. Extension work runs late far more often than it runs early, and the worktop is close to the last thing in, so the date agreed at the start is rarely the date that happens. Where several kitchens are ordered together the sensible move is to take them all off one batch, because two slabs of the same name bought six months apart will not sit happily in the same building. Order the stone against the room, never against the drawing. Where a family has been living around a building site for months, the finish date carries more weight than any other part of the specification. Volume work tends to live at the entry end of the range, and the entry end is genuine stone rather than a compromise, since the lowest supply figure we quote is a sintered surface and not a thin laminate pretending to be one. Several kitchens at once should come off a single batch.

A run that stops in mid-air at the open end needs a finished end rather than a cut one, and that end takes the same edge work as the whole front. A shape like that nests kindly on a slab, so more of what gets bought ends up on the units and the rate per square metre behaves much as the brochure says it will. A mitre asks the pattern to turn a corner and be believed. Material is £110-£550 per square metre supply only, and templating, fabrication and fitting are quoted on their own lines.

Where a corner is a couple of degrees off, a mitre cut to a theoretical ninety degrees opens on the wall side and there is no closing it afterwards. A hob dropped into the middle of a length puts sustained warmth at the lip of a cut-out, and an engineered surface will yellow there across ten years where a natural one takes it without comment. Speckle hides the resin line a mitre leaves behind. Send the run lengths, say where the sink and hob will sit, and tell us which way the room faces and what lighting is going in above the working run. The same building type can arrive as a careful one-off kitchen or as a fast turnaround, and the honest answer is that they are priced differently. That changes which questions are worth asking about the stone, because somebody staying put wants to know how a honed face marks in five years and somebody selling wants to know how it photographs next spring. The maintenance budget and the household budget buy differently.

On a porous stone the grooved area is sealed with the rest, and it gets wet more than anything else. A groove set needs a clear stretch of worktop beside the bowl, so it competes with the run for length instead of being free surface. The alternative stands on the surface, so the choice is losing worktop permanently or only while you are draining. Ground floors fall away towards the garden across the whole footprint, so the units are packed up long before anything is measured for stone. Which stone belongs on top of all that is a separate question from the building itself, and it is the one with a figure attached, because supply alone runs from £110 to £550 per square metre before a single cut has been made. Porous or not porous is the fork in the road on day one.

Floors and units are protected before anything comes through the door. The workmanship guarantee runs 5 years on every kitchen we fit. A piece is never laid flat across a gap while it is moved, because that is how stone cracks unaided. A loading bay or a red route puts a clock on the unload, so the pieces come off in the order they will be fitted rather than the order they were loaded. Where a seam becomes unavoidable the choice of stone starts to matter, because a fine even speckle closes a joint almost invisibly and a broad vein simply will not. The seam is planned on the layout, not discovered in the room.

What comes out goes by the same route the new stone comes in by, which is why that route is walked before anything is lifted. Old laminate is light and awkward rather than heavy, so it is usually the easier half of the day. Tiling bonded to the wall behind usually comes away with the old top, so that wall is agreed beforehand. A drive behind an electric gate depends on somebody being in to open it and on the gate staying open while the load comes off. Sintered surfaces are the hardest of the three to machine and the messiest to cut wet, which is precisely why none of that happens on a public pavement. The packaging and the spent cartridges leave with the crew.

If a piece cannot be got in at all, we say so at the template rather than on the day. What decides it is not the width of the stairwell but the length of piece that can be turned in it. Splitting a run costs a join, and that is the price of getting stone into the room at all. The van gets close to the door and the stone comes off the tail lift onto a trolley, which is about the shortest carry we ever get. Brittleness travels badly, and a porcelain or sintered length is far less tolerant of being flexed on a turn than an engineered slab of identical size. The pieces either side of a break come off adjoining slab.