Bathroom worktops and vanity tops in Chadwell Heath

Yes. Chadwell Heath is on the patch, and the postcodes we work here are RM6. It is worked on our east London run, along with the rest of Barking and Dagenham. Having the van on the drive means the load can be staged, so the heavy pieces come off last and go straight in instead of standing outside. A vanity fit is a short visit with one or two pieces in it, so the van stands only for as long as it takes to walk them in. A bathroom slot is booked short and kept short. We template in your kitchen and fit in your kitchen, so there is nothing to visit and nothing to collect.

The chimney breast has almost always been taken out of the kitchen with the stack left standing above it, so that bay of wall is newer plasterwork on a different plane. Either way the walls are thin, the floor is boards over shallow joists and nothing meets at a right angle, so the vanity is scribed at both ends and the unit is fixed back to the wall as well as standing on the floor. Boarded floors give, and a vanity shows it at the tile line. Walls that bow along their length are the normal condition rather than the exception, and a straight-cut back edge will show a shadow gap at one end and touch at the other. Bathrooms carry the same problems in a smaller room, and a smaller room leaves a vanity nowhere to absorb them. The tap has to clear the reveal before the hole is drilled.

The van gets close to the door and the stone comes off the tail lift onto a trolley, which is about the shortest carry we ever get. A vanity is the one piece of stone that route will not usually defeat, because a top cut to a standard unit depth weighs what one person can manage. Nothing is stood on edge once the tap holes are drilled. A dropped kerb wide enough for a car is not always wide enough for a long-wheelbase van, and the width of the crossing decides the rest. Where the van cannot wait, the top, the shelves and the adhesive all come in on the first trip and the van goes. Everything the bathroom needs comes off the van at once.

Not really, and there is no sense dressing it up. What the research on this patch actually lists is worktop templating, worktop installation and worktop replacement. That is a statement about the local housing rather than about the work. It gets quoted, cut and fitted exactly as it would anywhere else on the patch. Households sharing a house tend to want two prep areas rather than one, which usually means an island as well as a perimeter run. Work of that kind brings en-suites with it, and an en-suite vanity is a smaller piece again carrying exactly the same four operations. The vanity is the piece that makes a converted flat read finished. A second kitchen or a kitchenette in an annexe is a small job with the same fixed template, fabrication and fitting lines as a large one. Where several bathrooms are done in one building the tops come off one slab run, because two greys from two batches sit badly on adjoining floors. Several vanity tops off one slab run, or they will not match.

A full-depth tall unit projects past the worktop line, and the run has to be scribed against its side panel instead of carrying on past it. That shape decides what is left on the slab when the kitchen has been cut, and what is left on the slab is where most vanity tops come from. The waste from a basin aperture is what a shelf is cut from. Material sits between £110 and £550 per square metre supply only, and templating, fabrication and fitting are quoted line by line.

A run can measure dead right at both ends and still belly out in the middle, which only appears once the template plots the intermediate points. A vanity has no depth to lose, so where a kitchen run would take a ten millimetre scribe without noticing, a shallow top cannot spare it. A pipe boxing gets a radiused notch, never a square one. Have the vanity unit fixed and levelled, and the basin and tap on site, before the templater arrives, and tell us what is inside any boxing. Residents are given written notice before anyone attends, and that notice period rather than the workshop is what governs the earliest sensible start. Who is paying decides the material here more than anywhere else, because a vanity is small enough that an expensive stone stops being an expensive decision. The stone outlasts the unit under it, whoever owns the flat.

The same firm templates and fits. Nobody else is brought in to install. Between the template and the fit the slab is nested, cut, mitred and dry-assembled on the bench, which is work you never see and is most of the wait. Upstands and splashbacks are templated after the worktop is down and settled, so they are a separate visit. The original front door is narrow and the hall is often the only way in, which puts a ceiling on the longest single piece. What that does to a vanity is push the whole job into a narrow depth, because a bathroom takes the same stone as a kitchen in about two thirds of the width. The same stone as the kitchen, in a narrower cut.

A groove set needs a clear stretch of worktop beside the bowl, so it competes with the run for length instead of being free surface. The alternative stands on the surface, so the choice is losing worktop permanently or only while you are draining. Grooves are machined in the workshop at the same time as the bowl cut-out, because they cannot be done well in a kitchen. There is usually a step down into the back addition, so the kitchen floor and the hall floor are not the same level and neither of them is flat. A vanity top is where all of that turns up in miniature, with the basin, the tap holes and a splash return crowded into a few hundred millimetres of stone. Most vanity tops begin life as an offcut from another room.

Sealing is the one maintenance job that genuinely differs by material, and it is worth knowing which you are buying before the slab is chosen. Day to day all three want soap and water; abrasive creams and scouring pads are what dull a polished surface. Where a top takes wine, oil and lemon most days, the non-porous materials ask least of the household. Ceilings are high in these, so wall unit heights and splashback heights are open choices rather than things the room has already decided. The bathroom in one of these is usually a later addition over the back kitchen, so the walls are thinner, the floor moves and a vanity has to sit level in a room that is not. A rear addition bathroom is cold, narrow and full of pipework.

Where there is a lift, whether it can be booked out and padded matters as much as its size. Doorways, the newel post and the handrail usually take the room away, rather than the stairs themselves. If a piece cannot be got in at all, we say so at the template rather than on the day. A short hard approach with no steps means a full-length piece can be walked in flat by two people rather than turned up on edge. The exception is a double vanity, which is a kitchen length in bathroom width and behaves like a worktop from the tail lift onwards. A double vanity is a worktop as far as the carry is concerned.