Worktops in Covent Garden

Yes. Covent Garden is on the patch, and the postcodes we work here are WC2. It is worked on our central and north London run, along with the rest of Camden. Where a marked loading box sits on the red route the stop is legal but timed, so the unload runs as one movement with every hand on it. Whatever the standing allows, the stone leaves that van finished, because every edge, cut-out and internal radius is machined at the works and none of it is open to reconsideration at the kerb. Colour matched resin is mixed to the slab, not to a chart. Template and fit both happen at the property, so there is nothing to drive to and nothing to collect.

A basement kitchen has a flagged or concrete floor laid straight onto the ground, so it is solid, cold and rarely within ten millimetres of level. Alcoves either side of the old breast chop the run into short lengths, and a kitchen made of short lengths is the case where buying a slab outright beats buying the square metres, because the remainder is paid for in both. Four visible edges make the profile part of the design. Where the boxing stands proud of the finished wall the upstand behind it has to be broken into separate lengths, because one piece cannot pass it. Every notch and every scribe is machined into the piece before it leaves the works, and a hard sintered surface is the least forgiving of a tight internal corner, so one is always cut with a generous radius. Short lengths are where a full slab starts to pay for itself.

There is no leaning a piece against a wall halfway up, so any flight longer than a dozen treads is planned around a rest point on a landing. That caps the longest piece, and a run split into two lengths nests differently on the slab, which moves the yield and moves the figure with it. Thinner stone carries easily and asks for continuous support. A bus lane along the frontage brings its own hours with it, and stopping in one is enforced the same way the red route is. A granite kitchen ends its day with a sealer, and a sealer wants a dry face and a quiet hour afterwards, so that hour is written into the day rather than borrowed from it. Thirty millimetre stone unloads slowly and thin stone does not.

Not particularly. It would be easy to say yes and leave it there. What the research on this patch actually lists is worktop replacement and worktop splashbacks & upstands. That is about what people have here rather than how it gets done. It is quoted, cut and fitted exactly the same way here as anywhere else on the patch. A converted flat is measured off the original house, so no two units in the same building have quite the same kitchen run. Where several kitchens are ordered together the sensible move is to take them all off one batch, because two slabs of the same name bought six months apart will not sit happily in the same building. Movement across three metres is not visible on a hand sample. Kitchens go in near the end of a conversion, behind the plastering and the flooring, by which point the programme has already absorbed whatever slipped earlier. Volume work tends to live at the entry end of the range, and the entry end is genuine stone rather than a compromise, since the lowest supply figure we quote is a sintered surface and not a thin laminate pretending to be one. A repeated specification is worth deciding slowly, once.

Where a run finishes hard against a wall the last few millimetres are scribed, and where it finishes in open floor it is cut square and polished, which is two different jobs on one length. A shape like that nests kindly on a slab, so more of what gets bought ends up on the units and the rate per square metre behaves much as the brochure says it will. Edge metreage climbs with corners, not with floor area. Material runs £110 to £550 per square metre supply only, and templating, fabrication and fitting each get their own line.

A boxed soil stack or service riser in the corner of a run eats into the worktop depth and has to be scribed around rather than cut square. A hob dropped into the middle of a length puts sustained warmth at the lip of a cut-out, and an engineered surface will yellow there across ten years where a natural one takes it without comment. The narrowest return in the kitchen is its weakest stone. Send the run lengths, say where the sink and hob will sit, and tell us which way the room faces and what lighting is going in above the working run. One owner can take a date next week while the flat below needs three weeks of notice, so several kitchens in one building end up scheduled by the slowest permission. That changes which questions are worth asking about the stone, because somebody staying put wants to know how a honed face marks in five years and somebody selling wants to know how it photographs next spring. Twenty five years on the material, five on the workmanship.

Granite tells you when the seal wants topping up: water stops beading on the surface and starts darkening it instead. No maintenance visit is built into the job. Soap, water, and on the porous stones a seal. Marble is the one people underestimate. It is porous, like granite, and wants sealing. The closet wing is a narrow projection at the back with windows on two sides, which leaves very little continuous wall for a run. Rooms in these houses run long and narrow with the only honest daylight at the garden end, so a pale honed surface does more for the working half of the kitchen than any colour with depth in it. A low seam count is what makes a small kitchen good value.

A piece with a bowl and a hob cut into it is the fragile one, and it is handled accordingly. The tap hole is drilled in the workshop too, and its position depends on how far the tap has to swing. If the sink or hob changes after the template, the drawing changes first and nothing is cut meanwhile. A doorway partway along one wall breaks that side into two separate pieces, and two short pieces cost more between them than the single long one they replace. An island is the piece that decides whether one slab covers the kitchen or two, and a second slab arrives as a step in the figure rather than a gentle slope. A pale honed face earns its keep in a room short of daylight.

Templating, fabrication and fitting are the same three lines whether the stone came from us or from you. Thickness has to be known before quoting, since it decides the edge, the cut-outs and what the units carry. The quote is itemised, so a job where you already hold the slab is the same job with the material line taken off it. Studio and one-bed conversions put the whole kitchen against a single wall, so the job is one run and everything depends on that one length. Adding an island is what moves most of these projects from one slab to two, and that jump is the single largest step in any worktop quotation. Drawing lengths and room lengths are rarely the same lengths.

An external stair, a side return or a rear garden counts as carry and is measured the same way. Doorways, the newel post and the handrail usually take the room away, rather than the stairs themselves. The carry route is measured before anything is cut, so a piece that will not make the turn is split at the drawing stage rather than discovered on the day. Pendant fittings over the stairwell and anything hung on the half-landing come down first, because a piece on edge sweeps a wider arc than the people carrying it. Where a seam becomes unavoidable the choice of stone starts to matter, because a fine even speckle closes a joint almost invisibly and a broad vein simply will not. Vein direction is settled before the slab is broken into pieces.