Worktops in Joydens Wood

Yes. Joydens Wood is on the patch, and the postcodes we work here are DA5. It is worked on our south east London run, along with the rest of Bexley. Off-street parking means the van stays put all day, so tools, packers and the offcut we would rather have than not are all within reach. Whatever the standing allows, the stone leaves that van finished, because every edge, cut-out and internal radius is machined at the works and none of it is open to reconsideration at the kerb. Wet stone reads darker, which is why colour is judged indoors. Everything that involves you happens in your kitchen, so there is nothing to visit and nothing to collect.

The roof space above carries services, so a boiler flue or a soil vent can drop into a corner of the kitchen and stay exactly there. These kitchens are usually knocked through to the dining room, so the surface is read from two sides at once and the figure has to carry across the pieces rather than restart at every join. Plain stone takes the seam that a long carry forces. Old breasts carry a bulge low down where the original opening was closed up, and the units stand off it before the stone is measured at all. Every notch and every scribe is machined into the piece before it leaves the works, and a hard sintered surface is the least forgiving of a tight internal corner, so one is always cut with a generous radius. Water standing daily is what makes porosity matter.

The van gets close to the door and the stone comes off the tail lift onto a trolley, which is about the shortest carry we ever get. That caps the longest piece, and a run split into two lengths nests differently on the slab, which moves the yield and moves the figure with it. Speckle forgives a joint that a sweeping figure never would. A drive that shelves towards the house needs the van chocked and the trolley controlled, since a loaded A-frame gathers speed quickly on a slope. A granite kitchen ends its day with a sealer, and a sealer wants a dry face and a quiet hour afterwards, so that hour is written into the day rather than borrowed from it. Nothing is ever colour matched outdoors under a grey sky.

Not to any real extent, and it would be easy to imply it was. What the research on this patch actually lists is worktop installation. It describes the kitchens on this patch, not the work that goes into them. Same quoting, same cutting, same fitting as anywhere else on the patch. Extension kitchens are usually specified long before they are buildable, so the run lengths on the drawing and the run lengths in the room are different numbers. Where several kitchens are ordered together the sensible move is to take them all off one batch, because two slabs of the same name bought six months apart will not sit happily in the same building. Batch matching is the only honest way to match a surface. Extension work runs late far more often than it runs early, and the worktop is close to the last thing in, so the date agreed at the start is rarely the date that happens. Volume work tends to live at the entry end of the range, and the entry end is genuine stone rather than a compromise, since the lowest supply figure we quote is a sintered surface and not a thin laminate pretending to be one. The material is guaranteed for twenty five years, so choose once.

If the island is a few hundred millimetres longer than the usable length of a slab, a second slab gets bought to gain that overhang, and the whole slab is paid for rather than the part used. A shape like that nests kindly on a slab, so more of what gets bought ends up on the units and the rate per square metre behaves much as the brochure says it will. A mitre asks the pattern to turn a corner and be believed. Material sits between £110 and £550 per square metre supply only, and templating, fabrication and fitting are quoted line by line.

Two alcove pieces will not swap over however similar they look, so they are marked left and right at the bench and stay that way to the van. A hob dropped into the middle of a length puts sustained warmth at the lip of a cut-out, and an engineered surface will yellow there across ten years where a natural one takes it without comment. Brittle stone and narrow returns are a poor pairing. Confirm the depth of the units, the total run lengths and whether an island or peninsula is going in, and tell us the colour temperature of the lighting. An owner living in the house makes the decisions and lives with them, so the specification tends to go towards the material rather than towards the lowest total. That changes which questions are worth asking about the stone, because somebody staying put wants to know how a honed face marks in five years and somebody selling wants to know how it photographs next spring. Cleaning spray, not showroom light, should decide the finish.

A template on a normal kitchen takes two to three hours in the room. Templating and fitting are two visits, not one, and the gap between them is when the stone is actually cut. The template is taken in your kitchen after the units are in and fixed, never before. The extension slab was poured to its own level, so there is a lip or a ramp where the new floor meets the original one. Which stone belongs on top of all that is a separate question from the building itself, and it is the one with a figure attached, because supply alone runs from £110 to £550 per square metre before a single cut has been made. The slab is the decision; the room only sets how much of it you need.

If a piece cannot be got in at all, we say so at the template rather than on the day. The lift, if there is one, is measured on the diagonal, because that is the dimension a long piece actually uses. Doorways, the newel post and the handrail usually take the room away, rather than the stairs themselves. A short hard approach with no steps means a full-length piece can be walked in flat by two people rather than turned up on edge. Where a seam becomes unavoidable the choice of stone starts to matter, because a fine even speckle closes a joint almost invisibly and a broad vein simply will not. No colour and no edge is adjustable once a piece is machined.

Machining is permanent. If a later kitchen moves the sink, the grooves stay where they were cut. The alternative stands on the surface, so the choice is losing worktop permanently or only while you are draining. The bowl position has to be settled before templating, since the grooves are set out from it. Rear extensions on these sit on shallow foundations, and the crack at the junction with the original wall tells you which way it has moved. The surface is where the money actually moves: across the 181 kitchens fitted the median is £220 per square metre, and half of them land between £165 and £300. Supply is a range, and the room decides where in it you land.

Levelling belongs in the carcasses, on their own legs and packers. Units have to be fitted, fixed and level before templating, and it is better to hear that at the template than on the fitting day. A long top on units that were shimmed once and never checked is the commonest version of this, and it is cheap to fix beforehand. A chimney breast left in place splits a wall into two alcoves, and the two are rarely the same width and rarely parallel to each other. A run that sits under strong sun for hours every afternoon suits a surface built to be stable in daylight, because a resin-bound stone is made for indoor use and sustained sunlight is the one thing it was never designed around. What the room obstructs, the layout pays for in slab.