Worktops in Tufnell Park

Yes. Tufnell Park is on the patch, and the postcodes we work here are N7, NW5. It is worked on our central and north London run, along with the rest of Camden. A permit covering the street is permission to park rather than a space reserved on it, and on a full street the difference is the whole morning. Whatever the standing allows, the stone leaves that van finished, because every edge, cut-out and internal radius is machined at the works and none of it is open to reconsideration at the kerb. The film stays on the face until the last trade leaves. We come to the kitchen to template and again to fit, so there is nothing to visit and nothing to collect.

A basement is often reached by its own door under the front steps, and that door is smaller than anything else on the route. The kitchen in one of these sits in the back addition and takes its daylight from one end, so the working half of the run is the darker half and a pale stone with a honed or matt face does more there than any colour with depth in it. A galley nests efficiently and frees money for better stone. The stone carries the scribe because the wall cannot be persuaded, so back edges are cut oversize and eased in rather than dropped straight down. Every notch and every scribe is machined into the piece before it leaves the works, and a hard sintered surface is the least forgiving of a tight internal corner, so one is always cut with a generous radius. Speckle hides the resin line a mitre leaves behind.

A steep pitch shortens the tread and lengthens the reach, which leaves whoever is below carrying most of the weight for the full flight. That caps the longest piece, and a run split into two lengths nests differently on the slab, which moves the yield and moves the figure with it. The pieces either side of a break come off adjoining slab. Where the household has used up the visitor permits it gets for the year, the remaining options are a suspension or a paid bay and both belong on the quote. A granite kitchen ends its day with a sealer, and a sealer wants a dry face and a quiet hour afterwards, so that hour is written into the day rather than borrowed from it. Four quartz samples arrive by post, well before anything else does.

Not particularly, and it would be easy to pretend otherwise. What the research on this patch actually lists is worktop replacement and worktop installation. That is a point about the buildings round here, not about the job. The quoting, the cutting and the fitting are identical here to anywhere else we work. A kitchen carved out of a larger room sits under whatever the original plan left behind, so the run frequently ends at a blocked doorway or a boxed-in service. Where several kitchens are ordered together the sensible move is to take them all off one batch, because two slabs of the same name bought six months apart will not sit happily in the same building. The entry end of the range is real stone, not a compromise. Conversions put kitchens where the services could be made to reach rather than where they belong, so runs are short and interrupted. Volume work tends to live at the entry end of the range, and the entry end is genuine stone rather than a compromise, since the lowest supply figure we quote is a sintered surface and not a thin laminate pretending to be one. The island is usually what turns one slab into two.

On a heavily veined stone the island and the run behind it are nested off the same area of slab so the movement relates across the room. A shape like that nests kindly on a slab, so more of what gets bought ends up on the units and the rate per square metre behaves much as the brochure says it will. The shape sets the cut list and the cut list sets the stone bill. The stone is £110 to £550 per square metre supply only, and templating, fabrication and fitting are quoted separately.

A room can be out of square in both directions at once, so the wall that leans is also the wall that runs downhill, and one scribe cannot answer both. A hob dropped into the middle of a length puts sustained warmth at the lip of a cut-out, and an engineered surface will yellow there across ten years where a natural one takes it without comment. Every notch is machined on the bench and none on site. Send the run lengths, say where the sink and hob will sit, and tell us which way the room faces and what lighting is going in above the working run. The same building type can arrive as a careful one-off kitchen or as a fast turnaround, and the honest answer is that they are priced differently. That changes which questions are worth asking about the stone, because somebody staying put wants to know how a honed face marks in five years and somebody selling wants to know how it photographs next spring. Repairability is a fair question to ask before choosing.

A join sits over a cabinet gable. It never spans a gap and never runs through a cut-out. An island often runs in one piece where a wall run cannot. Join count is a question about slab size and run length, nothing else. Seating overhangs past roughly 300mm will not carry on the carcass alone, so flat steel bar or a plywood substrate has to be built into the units first. An island is the piece that decides whether one slab covers the kitchen or two, and a second slab arrives as a step in the figure rather than a gentle slope. Yield is a property of the room as much as of the slab.

No maintenance visit is built into the job. Soap, water, and on the porous stones a seal. A seal is not waterproofing. It only buys time to wipe a spill up. Bleach and limescale remover harm a polished finish rather than clean it, whichever material is on the units. Georgian houses put the kitchen in a basement or a rear closet wing, and the stairs down to it are the tightest part of the whole route. Alcoves either side of the old breast chop the run into short lengths, and a kitchen made of short lengths is the case where buying a slab outright beats buying the square metres, because the remainder is paid for in both. Plain stone takes the seam that a long carry forces.

The tap and waste have to be disconnected by a plumber before we start and reconnected once the stone is in. The sink and hob are lifted out with the old top and kept aside if you are reusing them. An old stone top is heavier coming out than the new one is going in, and leaves in sections. Estate roads inside a controlled zone are sometimes managed privately rather than by the council, which changes who has to be asked. Sintered surfaces are the hardest of the three to machine and the messiest to cut wet, which is precisely why none of that happens on a public pavement. Pieces are unloaded in laying order so the figure runs true.

Two kitchens the same length can be far apart, because material, edge and cut-outs move independently of size. Material is quoted supply only and templating, fabrication and fitting sit on their own lines, so it is visible which part is stone and which is labour. What moves the figure after templating is a change you make: a different edge, an extra cut-out, a bigger sink chosen late. Plaster thickness varies over the height of a wall, so the line at worktop height is not the line at skirting level, and the units decide which one matters. A run that sits under strong sun for hours every afternoon suits a surface built to be stable in daylight, because a resin-bound stone is made for indoor use and sustained sunlight is the one thing it was never designed around. Water standing daily is what makes porosity matter.