Worktops in Angel

Yes. Angel is on the patch, and the postcodes we work here are N1, EC1. It is worked on our north London run, along with the rest of Islington. A red route means no stopping, and no stopping means exactly that, so the stone comes in from a side street or from a bay behind the property. Whatever the standing allows, the stone leaves that van finished, because every edge, cut-out and internal radius is machined at the works and none of it is open to reconsideration at the kerb. The film stays on the face until the last trade leaves. Template and fit both happen at the property, so there is nothing to drive to and nothing to collect.

The closet wing is a narrow projection at the back with windows on two sides, which leaves very little continuous wall for a run. Rooms in these houses run long and narrow with the only honest daylight at the garden end, so a pale honed surface does more for the working half of the kitchen than any colour with depth in it. Even light lets a mid-tone hold its own. Plaster thickness varies over the height of a wall, so the line at worktop height is not the line at skirting level, and the units decide which one matters. Every notch and every scribe is machined into the piece before it leaves the works, and a hard sintered surface is the least forgiving of a tight internal corner, so one is always cut with a generous radius. Speckle hides the resin line a mitre leaves behind.

Grass and gravel will not take a loaded trolley, so a boarded track gets laid from the gate to the door before the first piece moves. That caps the longest piece, and a run split into two lengths nests differently on the slab, which moves the yield and moves the figure with it. Weight per square metre belongs to the material, not to the length. Where the frontage is a clearway the unload happens away from the door and the carry gets longer, which is a crew and time question rather than a stone one. A granite kitchen ends its day with a sealer, and a sealer wants a dry face and a quiet hour afterwards, so that hour is written into the day rather than borrowed from it. Four quartz samples arrive by post, well before anything else does.

Not particularly. It would be easy to say yes and leave it there. What the research on this patch actually lists is worktop replacement and worktop installation. That is about what people have here rather than how it gets done. It is quoted, cut and fitted exactly the same way here as anywhere else on the patch. Conversions put kitchens where the services could be made to reach rather than where they belong, so runs are short and interrupted. Where several kitchens are ordered together the sensible move is to take them all off one batch, because two slabs of the same name bought six months apart will not sit happily in the same building. A small kitchen still buys the remainder of the slab. In a converted house the flat entrance and the internal doorway are usually tighter than the communal stairs, and that is easy to overlook. Volume work tends to live at the entry end of the range, and the entry end is genuine stone rather than a compromise, since the lowest supply figure we quote is a sintered surface and not a thin laminate pretending to be one. Colour names outlive their batches by several years.

Galley runs are usually short enough to come out of a single slab, so the material band you choose does more to the total than the room shape does. A shape like that nests kindly on a slab, so more of what gets bought ends up on the units and the rate per square metre behaves much as the brochure says it will. Cut-outs take material out of the piece that carries the sink. Material runs £110 to £550 per square metre supply only, and templating, fabrication and fitting each get their own line.

Two walls each a degree out give an internal corner two degrees out, and the whole of that error lands in the mitre. A hob dropped into the middle of a length puts sustained warmth at the lip of a cut-out, and an engineered surface will yellow there across ten years where a natural one takes it without comment. Every notch is machined on the bench and none on site. Send the run lengths, say where the sink and hob will sit, and tell us which way the room faces and what lighting is going in above the working run. Mixed ownership means the decision-maker is not always the person who lets us in, so it is worth being clear early about who signs the quote off. That changes which questions are worth asking about the stone, because somebody staying put wants to know how a honed face marks in five years and somebody selling wants to know how it photographs next spring. Durability is cheaper than taste over a ten year hold.

Granite tells you when the seal wants topping up: water stops beading on the surface and starts darkening it instead. No maintenance visit is built into the job. Soap, water, and on the porous stones a seal. Granite is porous to varying degrees, so it is sealed when we fit it and topped up over the life of the worktop. Original panelling and shutter boxes stand out from the structural wall, so the face the units meet is joinery rather than plaster. The alcoves either side of a breast break the run into short pieces, and short pieces are exactly where buying a full slab outright starts to beat buying stone by the metre. Save on the colour before you save on the thickness.

Undermount bowls are cut and polished in the workshop and dry-fitted to the stone on the bench before anything is loaded. Nothing is cut out in the kitchen. Cutting a bowl on site is how worktops get cracked. If the sink or hob changes after the template, the drawing changes first and nothing is cut meanwhile. The walkway between the two runs is fixed by the units either side, so any overhang added to one worktop comes straight off the space somebody has to stand in. An island is the piece that decides whether one slab covers the kitchen or two, and a second slab arrives as a step in the figure rather than a gentle slope. Extra depth sounds free and frequently buys another slab.

Packing takes up small variation. It is not there to hide something that belongs in the units. Where a run meets an appliance, level decides whether that appliance door still clears the stone above it. Variation past what packing can take up has to be corrected in the carcasses before we cut, because the template records the units as they stand. A scribe has a working limit, and past twenty millimetres or so the back edge starts eating depth the run cannot spare. A run that sits under strong sun for hours every afternoon suits a surface built to be stable in daylight, because a resin-bound stone is made for indoor use and sustained sunlight is the one thing it was never designed around. Water standing daily is what makes porosity matter.

A mitred join at a corner is a different job from a butt join along a run, and they are not priced the same. Dark and heavily veined stone shows a join more than a pale even one, which is worth knowing before the slab is picked. Each join is an item on the drawing, so the layout and the figure move together. Both runs are in view at the same time, so the two pieces are taken off the same area of slab and the veining is set to run the same way on each side. A mitred corner asks the pattern to turn through a right angle, which an even speckle does without comment and a marble-look stone makes a performance of. Where the run beats the slab, the stone decides how the seam reads.