Worktops in Bishop's Park

Yes. Bishop's Park is on the patch, and the postcodes we work here are SW6. It is worked on our west London run, along with the rest of Hammersmith and Fulham. A timed school street shuts the road either side of the school day, so the van goes in between those two windows or it does not go in. Whatever the standing allows, the stone leaves that van finished, because every edge, cut-out and internal radius is machined at the works and none of it is open to reconsideration at the kerb. Nothing is ever colour matched outdoors under a grey sky. There is nothing to drive to and nothing to pick up, because both visits are to the property itself.

The addition wall is half a brick thick in places and has usually had a damp course injected and been re-plastered, which leaves it neither flat nor consistent. The kitchen in one of these sits in the back addition and takes its daylight from one end, so the working half of the run is the darker half and a pale stone with a honed or matt face does more there than any colour with depth in it. Side light flatters movement and wastes a flat colour. A cill projecting forward of the plaster line pushes the back edge out, and the units then stand off the wall by that amount for the whole length. Every notch and every scribe is machined into the piece before it leaves the works, and a hard sintered surface is the least forgiving of a tight internal corner, so one is always cut with a generous radius. Every notch is machined on the bench and none on site.

Boxed-in pipework running along the skirting looks harmless until a loaded trolley has to pass it. That caps the longest piece, and a run split into two lengths nests differently on the slab, which moves the yield and moves the figure with it. No colour and no edge is adjustable once a piece is machined. An event-day suspension can override a bay that is perfectly usable the rest of the week, so a booked space gets checked again nearer the time. A granite kitchen ends its day with a sealer, and a sealer wants a dry face and a quiet hour afterwards, so that hour is written into the day rather than borrowed from it. The film stays on the face until the last trade leaves.

Not particularly. It would be easy to say yes and leave it there. What the research on this patch actually lists is worktop installation and worktop replacement. That is about what people have here rather than how it gets done. It is quoted, cut and fitted exactly the same way here as anywhere else on the patch. Where a family has been living around a building site for months, the finish date carries more weight than any other part of the specification. Where several kitchens are ordered together the sensible move is to take them all off one batch, because two slabs of the same name bought six months apart will not sit happily in the same building. The island is usually what turns one slab into two. An open-plan extension puts the worktop in the middle of the living space, so it is looked at from the sofa as well as worked on. Volume work tends to live at the entry end of the range, and the entry end is genuine stone rather than a compromise, since the lowest supply figure we quote is a sintered surface and not a thin laminate pretending to be one. Where tenants change often, a surface with nothing to seal wins.

Peninsula tops are often the longest single piece in the kitchen, so if anything in the layout is going to force a second slab it is generally this one. A shape like that nests kindly on a slab, so more of what gets bought ends up on the units and the rate per square metre behaves much as the brochure says it will. Finished ends cost by the metre, however short the run is. Material runs £110 to £550 per square metre supply only, and templating, fabrication and fitting each get their own line.

Where the sill lands inside the height an upstand would occupy there is no upstand, and the stone either dies into the reveal or stops short of it. A hob dropped into the middle of a length puts sustained warmth at the lip of a cut-out, and an engineered surface will yellow there across ten years where a natural one takes it without comment. Water standing daily is what makes porosity matter. Send the run lengths, say where the sink and hob will sit, and tell us which way the room faces and what lighting is going in above the working run. Some doors in a building need a consent letter and some need nothing at all, so the first question is which arrangement applies here rather than which one is usual. That changes which questions are worth asking about the stone, because somebody staying put wants to know how a honed face marks in five years and somebody selling wants to know how it photographs next spring. Staying put and selling on ask different questions of a stone.

A long top on units that were shimmed once and never checked is the commonest version of this, and it is cheap to fix beforehand. If the carcasses are corrected, the template is taken again, since a drawing off units that then moved is worthless. Levelling belongs in the carcasses, on their own legs and packers. Casement handles and stays swing down into the space above the worktop, so the clearance that counts is the one measured with the window open. A run that sits under strong sun for hours every afternoon suits a surface built to be stable in daylight, because a resin-bound stone is made for indoor use and sustained sunlight is the one thing it was never designed around. Brittle stone and narrow returns are a poor pairing.

Each join is an item on the drawing, so the layout and the figure move together. Join count and position are settled from the template drawing rather than improvised on the fitting day. There are only ever a few legal positions, and the one taken is furthest from the light. A peninsula is an island with one end tied to a run, which means the join between them has to be planned rather than allowed to happen. An island is the piece that decides whether one slab covers the kitchen or two, and a second slab arrives as a step in the figure rather than a gentle slope. Cut-outs take material out of the piece that carries the sink.

Which side of the bowl they go is about how you stand at the sink, and it is settled before cutting. Where there is no room for a separate drainer, grooves are usually what gets specified instead. They are cut with a fall towards the bowl, which is why they cannot be added on site later. Ground floors fall away towards the garden across the whole footprint, so the units are packed up long before anything is measured for stone. Which stone belongs on top of all that is a separate question from the building itself, and it is the one with a figure attached, because supply alone runs from £110 to £550 per square metre before a single cut has been made. Yield is the word behind most quotations people did not expect.

Upstand or splashback, the stone is cut from the same slab run as the worktop, at the same time, so the batch actually matches. Stone up a wall is heavier than tile and bonded rather than hung, so the wall has to be sound. An upstand covers the gap where the worktop meets a wall that is not flat, which is its real job. Where the side return has been filled in, the old external wall is now an internal one and still carries its render, its gutter line and its old fixings. Alcoves either side of the old breast chop the run into short lengths, and a kitchen made of short lengths is the case where buying a slab outright beats buying the square metres, because the remainder is paid for in both. One full slab and no second is the sweet spot on price.