Bathroom worktops and vanity tops in Crayford

Yes. Crayford is on the patch, and the postcodes we work here are DA1. It is worked on our south east London run, along with the rest of Bexley. Unrestricted kerbside is straightforward as long as the space in front of the property is actually clear when the van arrives. A vanity fit is a short visit with one or two pieces in it, so the van stands only for as long as it takes to walk them in. No basin aperture is worth rushing for a parking bay. Your part of it happens entirely at home, with nothing to travel to and nothing to bring back.

The goods lift is generous and the flat entrance often is not, so the tightest point on the route is inside the flat rather than in the building. Bathrooms in these buildings are pods built inside the shell, so the walls are new square studwork and the room was set out on paper rather than inherited. The soil stack decides the basin position more than taste does. Sill height gets settled with the template on site, because it is one of the few dimensions nobody has measured before we arrive. Bathrooms carry the same problems in a smaller room, and a smaller room leaves a vanity nowhere to absorb them. Wall-hung means the wall carries the basin, so the wall gets checked.

Bollards, planters and a one-way service road can turn what looks like a ten-metre carry into a fifty-metre one. A vanity is the one piece of stone that route will not usually defeat, because a top cut to a standard unit depth weighs what one person can manage. The piece is carried by its long edges, never by the aperture. On a street with no restrictions the constraint is other residents rather than a warden, so it is worth putting a cone or a car out early. Where the van cannot wait, the top, the shelves and the adhesive all come in on the first trip and the van goes. The bathroom pieces come off last and go in first.

Not particularly, and it would be easy to pretend otherwise. What the research on this patch actually lists is worktop replacement, worktop templating and worktop fabrication. That is a point about the buildings round here, not about the job. The quoting, the cutting and the fitting are identical here to anywhere else we work. Where a family has been living around a building site for months, the finish date carries more weight than any other part of the specification. Work of that kind brings en-suites with it, and an en-suite vanity is a smaller piece again carrying exactly the same four operations. Repeat bathrooms come cheaper per top, not per square metre. An open-plan extension puts the worktop in the middle of the living space, so it is looked at from the sofa as well as worked on. Where several bathrooms are done in one building the tops come off one slab run, because two greys from two batches sit badly on adjoining floors. A converted house needs a vanity on every floor.

The joint where a peninsula meets the main run wants a gable directly under it, and where the units do not offer one, steel goes in to carry that joint instead. That shape decides what is left on the slab when the kitchen has been cut, and what is left on the slab is where most vanity tops come from. A cloakroom top is the easiest piece on any nesting plan. The material band is £110 to £550 per square metre supply only, and templating, fabrication and fitting are quoted on their own lines.

A window board sitting below finished worktop height leaves two choices, drop the top under it or notch the stone around it, and both cost more than a straight run. A vanity has no depth to lose, so where a kitchen run would take a ten millimetre scribe without noticing, a shallow top cannot spare it. The tile joint behind is what shows a top that is not level. Confirm what is behind the board where the unit hangs, and send the goods lift and door dimensions if the pieces include shelving. These kitchens tend to be compact and reasonably square, so the fixed template, fabrication and fitting lines are a larger share of the total than the stone is. Who is paying decides the material here more than anywhere else, because a vanity is small enough that an expensive stone stops being an expensive decision. Approval comes before the aperture is drawn, not after.

The check comes before the measuring rather than after, because the whole drawing is set out from that plane. Small variation is taken up by packing under the top on the fitting day. Units have to be fixed down as well as levelled. A loose carcass moves under stone. A cill projecting forward of the plaster line pushes the back edge out, and the units then stand off the wall by that amount for the whole length. The boxed soil stack in the corner is the usual version of it upstairs, and a top that notches round one loses depth exactly where the basin wanted it. A stud wall takes a vanity only once there is timber behind it.

Grooves and an undermounted bowl are usually specified together, since the grooves are run to the bowl edge. Grooves are machined into the surface rather than applied to it, so there is nothing to come loose later. They read strongly across a dark stone and are nearly invisible on a pale one, so look before deciding. Ceilings are high and every surface is hard, so cutting on site carries further here than in any other kind of building. What that does to a vanity is push the whole job into a narrow depth, because a bathroom takes the same stone as a kitchen in about two thirds of the width. A cloakroom top and an en-suite top are one job at two sizes.

Each join is an item on the drawing, so the layout and the figure move together. Join count is a question about slab size and run length, nothing else. What you get is a line rather than a step, because the pieces are levelled to each other first. A breakfast bar on the outer side is an overhang like any other, and the support under it is sized for people leaning on the end rather than for the weight of the stone alone. A bathroom ordered with the kitchen is taken from the same slab run, so the two rooms match rather than nearly match. Yield is why a vanity in a rare stone is still affordable.

The tap hole is drilled in the workshop too, and its position depends on how far the tap has to swing. We seat and seal the sink and hob on the day; water, waste, gas and electrics are for your plumber and electrician. A sit-on sink and an undermounted one are different cut-outs, so which it is gets settled before the template. A peninsula projects into circulation space, so its outer corners usually take a radius rather than a point, and that radius is agreed at template rather than assumed. Where the kitchen swallows the whole slab there is no offcut worth having, and the vanity then has to be priced against material bought for itself. Ordered later, the batch match is a gamble rather than a plan.