Worktops in Shepherd's Bush

Yes. Shepherd's Bush is on the patch, and the postcodes we work here are W12. It is worked on our west London run, along with the rest of Hammersmith and Fulham. Loading exemptions on red routes are narrow, time-limited and heavily camera-enforced, so we plan around them rather than relying on them. Whatever the standing allows, the stone leaves that van finished, because every edge, cut-out and internal radius is machined at the works and none of it is open to reconsideration at the kerb. Dust from a sintered slab belongs at the works, not on a street. Both visits happen in your kitchen, the template and the fit, so there is nothing to visit and nothing to collect.

Cornice, picture rails and deep skirting survive in converted rooms, so the run stands off the wall and the back edge follows the units rather than the plaster. The kitchen in one of these sits in the back addition and takes its daylight from one end, so the working half of the run is the darker half and a pale stone with a honed or matt face does more there than any colour with depth in it. Movement needs length, and length is what these rooms have. Legs bottoming out on hard concrete or an uneven screed mean the tops of the carcasses are not one plane, and that is picked up at template rather than on fitting day. Every notch and every scribe is machined into the piece before it leaves the works, and a hard sintered surface is the least forgiving of a tight internal corner, so one is always cut with a generous radius. Porous or sealed is a decision about the next ten years.

Open-tread and cantilevered stairs give nothing to lean a piece against, so the whole weight stays on the crew for the full length of the flight. That caps the longest piece, and a run split into two lengths nests differently on the slab, which moves the yield and moves the figure with it. Flexing a porcelain length round a turn is how one breaks. The realistic answer on a main road is an early slot, a spotter on the van and pieces staged in one movement rather than several trips. A granite kitchen ends its day with a sealer, and a sealer wants a dry face and a quiet hour afterwards, so that hour is written into the day rather than borrowed from it. The offcut is yours if you want it and ours if you do not.

Not particularly. It would be easy to say yes and leave it there. What the research on this patch actually lists is worktop replacement, worktop installation and worktop splashbacks & upstands. That is about what people have here rather than how it gets done. It is quoted, cut and fitted exactly the same way here as anywhere else on the patch. Where kitchens turn over between tenancies the priority is a surface that survives a decade of being treated as a chopping board. Where several kitchens are ordered together the sensible move is to take them all off one batch, because two slabs of the same name bought six months apart will not sit happily in the same building. The material is guaranteed for twenty five years, so choose once. Landlord work is scheduled around void periods, so the whole thing is a fixed window and the template date matters as much as the fitting date. Volume work tends to live at the entry end of the range, and the entry end is genuine stone rather than a compromise, since the lowest supply figure we quote is a sintered surface and not a thin laminate pretending to be one. Two slabs bought a season apart are two different stones.

Two parallel runs with a walkway between them is the most efficient shape there is on a slab, because both pieces nest as straight lengths with almost no waste. A shape like that nests kindly on a slab, so more of what gets bought ends up on the units and the rate per square metre behaves much as the brochure says it will. The number follows the layout far more closely than the floor plan. Expect £110 to £550 per square metre for material supply only, with templating, fabrication and fitting on their own lines.

Level has to hold across the whole room rather than along one wall, or a floor that falls end to end shows as a step where two pieces meet. A hob dropped into the middle of a length puts sustained warmth at the lip of a cut-out, and an engineered surface will yellow there across ten years where a natural one takes it without comment. A short upstand shows a fragment of pattern, never a run of it. Send the run lengths, say where the sink and hob will sit, and tell us which way the room faces and what lighting is going in above the working run. Where a letting agent sits between us and the owner the approval passes through two sets of hands, so a quote has to be clear enough to forward without a covering explanation. That changes which questions are worth asking about the stone, because somebody staying put wants to know how a honed face marks in five years and somebody selling wants to know how it photographs next spring. A surface nobody maintains should not need maintaining.

A join forced by the route still sits over a gable, so it is no poorer a join for that. The carry route is measured before anything is cut, so a piece that will not make the turn is split at the drawing stage rather than discovered on the day. Where there is a lift, whether it can be booked out and padded matters as much as its size. A handrail that has to come off before a piece will pass is twenty minutes at the start of the day, and it goes back on the wall before we leave. Where a seam becomes unavoidable the choice of stone starts to matter, because a fine even speckle closes a joint almost invisibly and a broad vein simply will not. Short pieces nest tighter, and tighter nesting is less stone bought.

Where there is no room for a separate drainer, grooves are usually what gets specified instead. Grooves and an undermounted bowl are usually specified together, since the grooves are run to the bowl edge. A groove set is its own item on the quote rather than something rolled in with the sink cut-out. Chimney breasts are often taken out at ground level and left standing above, so the middle of the run is newer wall than the two ends of it. Which stone belongs on top of all that is a separate question from the building itself, and it is the one with a figure attached, because supply alone runs from £110 to £550 per square metre before a single cut has been made. Two kitchens of one size can differ by double on the stone alone.

Two kitchens the same length can be far apart, because material, edge and cut-outs move independently of size. Taking the old tops away is a line rather than an assumption, so it comes off if you do not want it. Every run, cut-out, edge, join and groove set is a line, which is what makes it comparable with anyone else’s. A floor that falls across the depth of a run rather than along it tips the carcasses front to back, and packing the front feet changes the overhang while it fixes the level. A run that sits under strong sun for hours every afternoon suits a surface built to be stable in daylight, because a resin-bound stone is made for indoor use and sustained sunlight is the one thing it was never designed around. Reach across an unsupported span is a thickness question.

A mitred join at a corner is a different job from a butt join along a run, and they are not priced the same. What you get is a line rather than a step, because the pieces are levelled to each other first. There are only ever a few legal positions, and the one taken is furthest from the light. A galley puts the sink on one side and the hob on the other, which spreads the cut-outs across two pieces instead of weakening one. An island is the piece that decides whether one slab covers the kitchen or two, and a second slab arrives as a step in the figure rather than a gentle slope. A clean nest on the slab is the cheapest thing a shape can do.