Worktops in Wood Lane

Yes. Wood Lane is on the patch, and the postcodes we work here are W12. It is worked on our west London run, along with the rest of Hammersmith and Fulham. Underground loading has a height restriction, and a van with an A-frame on it is taller than the driver remembers. Whatever the standing allows, the stone leaves that van finished, because every edge, cut-out and internal radius is machined at the works and none of it is open to reconsideration at the kerb. Pieces are unloaded in laying order so the figure runs true. We template in your kitchen and fit in your kitchen, so there is nothing to visit and nothing to collect.

These houses are three storeys on a small footprint, so the kitchen is on the ground floor and everything else is stacked above it. Kitchens in these blocks are compact and open to the living space, so the surface is furniture as much as work surface and a quiet consistent stone carries that better than a dramatic one. Long narrow rooms want a pale face at the working end. Walls that bow along their length are the normal condition rather than the exception, and a straight-cut back edge will show a shadow gap at one end and touch at the other. Every notch and every scribe is machined into the piece before it leaves the works, and a hard sintered surface is the least forgiving of a tight internal corner, so one is always cut with a generous radius. Water standing daily is what makes porosity matter.

The barrier, the entry code and the estate rules decide when a van can get near the door, and none of that is negotiable on the day. That caps the longest piece, and a run split into two lengths nests differently on the slab, which moves the yield and moves the figure with it. Pattern is carried across a seam on the bench, never by eye on site. Where the bay sits some distance from the core, the carry across the car park is the longest leg of the day and gets boarded and lit. A granite kitchen ends its day with a sealer, and a sealer wants a dry face and a quiet hour afterwards, so that hour is written into the day rather than borrowed from it. A reserved slab is a slab nobody else is allowed to buy.

Not really, and there is no sense dressing it up. What the research on this patch actually lists is worktop replacement and worktop installation. That is a statement about the local housing rather than about the work. It gets quoted, cut and fitted exactly as it would anywhere else on the patch. In a converted house the flat entrance and the internal doorway are usually tighter than the communal stairs, and that is easy to overlook. Where several kitchens are ordered together the sensible move is to take them all off one batch, because two slabs of the same name bought six months apart will not sit happily in the same building. A small kitchen still buys the remainder of the slab. Party-wall and lease conditions in a converted building set when noisy work can happen, which shapes the fitting day more than the kitchen does. Volume work tends to live at the entry end of the range, and the entry end is genuine stone rather than a compromise, since the lowest supply figure we quote is a sintered surface and not a thin laminate pretending to be one. Colour names outlive their batches by several years.

Whether it comes off the same slab as the run behind it or needs one of its own is settled by laying both against the usable area of the slab, not by adding the metres up. A shape like that nests kindly on a slab, so more of what gets bought ends up on the units and the rate per square metre behaves much as the brochure says it will. Two mitres and three lengths is bench work, not surface area. Material is £110-£550 per square metre supply only, and templating, fabrication and fitting are quoted on their own lines.

A run can measure dead right at both ends and still belly out in the middle, which only appears once the template plots the intermediate points. A hob dropped into the middle of a length puts sustained warmth at the lip of a cut-out, and an engineered surface will yellow there across ten years where a natural one takes it without comment. Brittle stone and narrow returns are a poor pairing. Send the kitchen layout with run lengths and the peninsula projection if there is one, and tell us what the lift will take as a single piece. Flats bought out of managed stock keep the original kitchen dimensions long after the ownership changed, so the layout says very little about who is paying for the work. That changes which questions are worth asking about the stone, because somebody staying put wants to know how a honed face marks in five years and somebody selling wants to know how it photographs next spring. A surface chosen for a photograph rarely survives the cooking.

Doorways, the newel post and the handrail usually take the room away, rather than the stairs themselves. An external stair, a side return or a rear garden counts as carry and is measured the same way. The lift, if there is one, is measured on the diagonal, because that is the dimension a long piece actually uses. Estate roads are often too tight for a long-wheelbase van to turn, so the carry starts a good deal further from the door than a map suggests. Where a seam becomes unavoidable the choice of stone starts to matter, because a fine even speckle closes a joint almost invisibly and a broad vein simply will not. The way in caps the piece, and the slab layout follows the cap.

Veining carries through a join where both pieces come off the same slab, which is decided at nesting. A mitred join at a corner is a different job from a butt join along a run, and they are not priced the same. Slabs come in finite sizes, so a long run needs a join whatever the room looks like. The offcut taken out of the middle for a hob is a large usable piece, and it is worth deciding early whether it becomes an upstand or goes in the skip. An island is the piece that decides whether one slab covers the kitchen or two, and a second slab arrives as a step in the figure rather than a gentle slope. A single straight run is the cheapest stone you will ever buy.

If you want the old top kept for a garage or a utility, say so and it stays on site. Old tops are screwed or glued from underneath, so the drawer boxes come out before the worktop does. Old laminate is light and awkward rather than heavy, so it is usually the easier half of the day. The goods lift has its own booking sheet, and a bay slot without a lift slot only gets the stone as far as the lobby. Sintered surfaces are the hardest of the three to machine and the messiest to cut wet, which is precisely why none of that happens on a public pavement. Cutting is done wet and extracted, never dry on a pavement.

What moves the figure after templating is a change you make: a different edge, an extra cut-out, a bigger sink chosen late. Nothing is payable until the template, and the template measures the room as it stands rather than estimating from a plan. Cut-outs, edge profile and join count are itemised, so taking one out removes a line rather than starting an argument. Where a corner is a couple of degrees off, a mitre cut to a theoretical ninety degrees opens on the wall side and there is no closing it afterwards. A run that sits under strong sun for hours every afternoon suits a surface built to be stable in daylight, because a resin-bound stone is made for indoor use and sustained sunlight is the one thing it was never designed around. What the room obstructs, the layout pays for in slab.