Worktops in Tottenham

Yes. Tottenham is on the patch, and the postcodes we work here are N17. It is worked on our north London run, along with the rest of Haringey. Where the van cannot turn on the plot it has to arrive already facing the right way, so the approach along the street is part of the plan. Whatever the standing allows, the stone leaves that van finished, because every edge, cut-out and internal radius is machined at the works and none of it is open to reconsideration at the kerb. Thirty millimetre stone unloads slowly and thin stone does not. We template in your kitchen and fit in your kitchen, so there is nothing to visit and nothing to collect.

Where the kitchen has taken the bay, the end of the room is three facets of glass set at angles and there is no straight wall left to finish against. The kitchen in one of these sits in the back addition and takes its daylight from one end, so the working half of the run is the darker half and a pale stone with a honed or matt face does more there than any colour with depth in it. Four visible edges make the profile part of the design. Where a corner is a couple of degrees off, a mitre cut to a theoretical ninety degrees opens on the wall side and there is no closing it afterwards. Every notch and every scribe is machined into the piece before it leaves the works, and a hard sintered surface is the least forgiving of a tight internal corner, so one is always cut with a generous radius. Speckle hides the resin line a mitre leaves behind.

Whether the stone can stand on end in the car is the first question, because a lift that takes 2.1m upright takes nothing like that lying flat. That caps the longest piece, and a run split into two lengths nests differently on the slab, which moves the yield and moves the figure with it. Speckle forgives a joint that a sweeping figure never would. A drive behind an electric gate depends on somebody being in to open it and on the gate staying open while the load comes off. A granite kitchen ends its day with a sealer, and a sealer wants a dry face and a quiet hour afterwards, so that hour is written into the day rather than borrowed from it. The packaging and the spent cartridges leave with the crew.

Not to any real extent, and it would be easy to imply it was. What the research on this patch actually lists is worktop replacement, worktop installation and worktop splashbacks & upstands. It describes the kitchens on this patch, not the work that goes into them. Same quoting, same cutting, same fitting as anywhere else on the patch. The person choosing the worktop is not the person using it, and that shifts the balance from appearance towards running cost. Where several kitchens are ordered together the sensible move is to take them all off one batch, because two slabs of the same name bought six months apart will not sit happily in the same building. Specify before the room is finished, not afterwards. Where kitchens turn over between tenancies the priority is a surface that survives a decade of being treated as a chopping board. Volume work tends to live at the entry end of the range, and the entry end is genuine stone rather than a compromise, since the lowest supply figure we quote is a sintered surface and not a thin laminate pretending to be one. Repeat work rewards a single decision taken carefully.

A tall bank of housings at one end takes a chunk out of the working run, so the usable length of that side is always less than the length of the wall behind it. A shape like that nests kindly on a slab, so more of what gets bought ends up on the units and the rate per square metre behaves much as the brochure says it will. The waterfall leg is a whole extra piece of stone. Stone is £110 to £550 per square metre supply only, and the templating, the fabrication and the fitting each carry their own line.

The stone carries the scribe because the wall cannot be persuaded, so back edges are cut oversize and eased in rather than dropped straight down. A hob dropped into the middle of a length puts sustained warmth at the lip of a cut-out, and an engineered surface will yellow there across ten years where a natural one takes it without comment. Every notch is machined on the bench and none on site. Send the run lengths, say where the sink and hob will sit, and tell us which way the room faces and what lighting is going in above the working run. Where the owner is not local, the decisions happen remotely, so photographs and a clear itemised drawing carry more weight than a showroom visit ever would. That changes which questions are worth asking about the stone, because somebody staying put wants to know how a honed face marks in five years and somebody selling wants to know how it photographs next spring. Cleaning spray, not showroom light, should decide the finish.

A template on a normal kitchen takes two to three hours in the room. Between the template and the fit the slab is nested, cut, mitred and dry-assembled on the bench, which is work you never see and is most of the wait. The same firm templates and fits. Nobody else is brought in to install. The side return was an outside toilet and a coal store before it was ever a kitchen, and the walls left over from that are half a brick thick. Which stone belongs on top of all that is a separate question from the building itself, and it is the one with a figure attached, because supply alone runs from £110 to £550 per square metre before a single cut has been made. Pick the surface for the cooking rather than for the photograph.

If a piece cannot be got in at all, we say so at the template rather than on the day. A piece travels on edge, never flat, because on edge is how stone of that length carries its own weight. A join forced by the route still sits over a gable, so it is no poorer a join for that. Goods lifts and passenger lifts fail differently: one has a rated load that matters, the other has a door aperture that matters more. Where a seam becomes unavoidable the choice of stone starts to matter, because a fine even speckle closes a joint almost invisibly and a broad vein simply will not. No colour and no edge is adjustable once a piece is machined.

Taking the old tops away is a line rather than an assumption, so it comes off if you do not want it. Plumbing, gas and electrical work are not in the figure, because we do not do them. Every run, cut-out, edge, join and groove set is a line, which is what makes it comparable with anyone else’s. A room can be out of square in both directions at once, so the wall that leans is also the wall that runs downhill, and one scribe cannot answer both. A run that sits under strong sun for hours every afternoon suits a surface built to be stable in daylight, because a resin-bound stone is made for indoor use and sustained sunlight is the one thing it was never designed around. Water standing daily is what makes porosity matter.

The bowl position has to be settled before templating, since the grooves are set out from it. On a porous stone the grooved area is sealed with the rest, and it gets wet more than anything else. Grooves are machined into the surface rather than applied to it, so there is nothing to come loose later. Party wall settlement pulls the floor down at one side of the room, so a long run reads level at one end and not at the other. The surface is where the money actually moves: across the 181 surfaces we list the median is £220 per square metre, and half of them sit between £165 and £300. The light in a room shortens the shortlist faster than the budget does.