Worktops in Richmond

Yes. Richmond is on the patch, and the postcodes we work here are TW9, TW10. It is worked on our south west London run, along with the rest of the borough. Loading concessions differ from one zone to the next rather than following a single national rule, so what applied on the last job proves nothing about this one. Whatever the standing allows, the stone leaves that van finished, because every edge, cut-out and internal radius is machined at the works and none of it is open to reconsideration at the kerb. The offcut is yours if you want it and ours if you do not. Nothing needs visiting and nothing needs collecting: the template is in your kitchen and so is the fit.

The original stair has an open well running the full height of the building, which occasionally lets a long piece go up vertically where it would never take the turns. The kitchen in one of these sits in the back addition and takes its daylight from one end, so the working half of the run is the darker half and a pale stone with a honed or matt face does more there than any colour with depth in it. Two slabs change the question from price to preference. Where two pieces meet over a fall in the floor the join has to be flush to the hand as well as true to the level, because the eye reads the join and forgives the room. Every notch and every scribe is machined into the piece before it leaves the works, and a hard sintered surface is the least forgiving of a tight internal corner, so one is always cut with a generous radius. Short lengths are where a full slab starts to pay for itself.

A rated load sounds ample until three lengths of granite and two fitters are standing on it, so the stone goes up one piece at a time. That caps the longest piece, and a run split into two lengths nests differently on the slab, which moves the yield and moves the figure with it. A remnant worth keeping rides back on the van rather than to a skip. A van waiting on a loading concession has somebody standing with it, because a vehicle left unattended is the one that collects the ticket. A granite kitchen ends its day with a sealer, and a sealer wants a dry face and a quiet hour afterwards, so that hour is written into the day rather than borrowed from it. A sealer needs a dry face and a quiet hour after it.

Not to any real extent, and it would be easy to imply it was. What the research on this patch actually lists is worktop replacement and worktop installation. It describes the kitchens on this patch, not the work that goes into them. Same quoting, same cutting, same fitting as anywhere else on the patch. A licensed shared house has fire-door and escape-route rules that decide how and when stone can be carried through the common parts. Where several kitchens are ordered together the sensible move is to take them all off one batch, because two slabs of the same name bought six months apart will not sit happily in the same building. Drawing lengths and room lengths are rarely the same lengths. Four kitchens ordered together take one template visit and one delivery, and that is where the saving comes from rather than from a discount on the stone. Volume work tends to live at the entry end of the range, and the entry end is genuine stone rather than a compromise, since the lowest supply figure we quote is a sintered surface and not a thin laminate pretending to be one. The cheapest stone we fit is sintered, and it is still stone.

A doorway partway along one wall breaks that side into two separate pieces, and two short pieces cost more between them than the single long one they replace. A shape like that nests kindly on a slab, so more of what gets bought ends up on the units and the rate per square metre behaves much as the brochure says it will. Long unbroken lengths are what make a plain stone look dear. Material sits between £110 and £550 per square metre supply only, and templating, fabrication and fitting are quoted line by line.

Floors settle, and once base units are packed and levelled properly the stone sits true while everything else in the room admits it is not. A hob dropped into the middle of a length puts sustained warmth at the lip of a cut-out, and an engineered surface will yellow there across ten years where a natural one takes it without comment. The narrowest return in the kitchen is its weakest stone. Send the run lengths, say where the sink and hob will sit, and tell us which way the room faces and what lighting is going in above the working run. Two flats with an identical layout can want entirely different things from the same run of worktop, which is why the quote follows the run rather than the address. That changes which questions are worth asking about the stone, because somebody staying put wants to know how a honed face marks in five years and somebody selling wants to know how it photographs next spring. Neutral mid-tones survive a change of owner better than statements.

On a replacement the old top comes off in the morning and the new stone is down and sealed the same day. Tiling bonded to the wall behind usually comes away with the old top, so that wall is agreed beforehand. Take the old tops off yourself if you would rather, and the quote simply carries one line fewer. Controlled hours that end in the middle of the afternoon make the second half of the day easy and put the whole problem in the first half. Sintered surfaces are the hardest of the three to machine and the messiest to cut wet, which is precisely why none of that happens on a public pavement. Wet stone reads darker, which is why colour is judged indoors.

Sealing is the one maintenance job that genuinely differs by material, and it is worth knowing which you are buying before the slab is chosen. Day to day all three want soap and water; abrasive creams and scouring pads are what dull a polished surface. Quartz and sintered stone never need sealing: quartz is non-porous and sintered stone has effectively zero porosity. Winders at the head of each flight are the tightest part of the climb and they are appreciably tighter than the straight run below them. The alcoves either side of a breast break the run into short pieces, and short pieces are exactly where buying a full slab outright starts to beat buying stone by the metre. The island earns the liveliest part of the stone.

The fitting itself is one visit: a plain run is a morning, an island with splashbacks takes most of the day. Nothing is measured until the sink, the tap and the hob are in the room to measure against. Between the template and the fit the slab is nested, cut, mitred and dry-assembled on the bench, which is work you never see and is most of the wait. Nothing in a house of this age is square, and the kitchen is usually the part that has been altered most often. Which stone belongs on top of all that is a separate question from the building itself, and it is the one with a figure attached, because supply alone runs from £110 to £550 per square metre before a single cut has been made. Edges are charged along their length, not across the surface.

A groove set needs a clear stretch of worktop beside the bowl, so it competes with the run for length instead of being free surface. The alternative stands on the surface, so the choice is losing worktop permanently or only while you are draining. Grooves are machined into the surface rather than applied to it, so there is nothing to come loose later. The kitchen normally sits in the back addition or a later side return, which puts the run against the oldest and least straight wall in the building. The surface is where the money actually moves: across the 181 kitchens fitted the median is £220 per square metre, and half of them land between £165 and £300. Two kitchens of one size can differ by double on the stone alone.