Worktops in Temple

Yes. Temple is on the patch, and the postcodes we work here are EC4Y. It is worked on our City of London run, along with the rest of the Square Mile. Unrestricted kerbside is straightforward as long as the space in front of the property is actually clear when the van arrives. Whatever the standing allows, the stone leaves that van finished, because every edge, cut-out and internal radius is machined at the works and none of it is open to reconsideration at the kerb. The offcut is yours if you want it and ours if you do not. Template and fit both happen at the property, so there is nothing to drive to and nothing to collect.

Edwardian terraces are wider and taller than the Victorian houses next to them, so the kitchen usually takes a full-width rear room rather than a narrow outrigger. The kitchen in one of these sits in the back addition and takes its daylight from one end, so the working half of the run is the darker half and a pale stone with a honed or matt face does more there than any colour with depth in it. Cool artificial light turns a warm stone grey. Where a breast interrupts a long wall the join can often go there, so it reads as a natural break rather than a line in the middle of a worktop. Every notch and every scribe is machined into the piece before it leaves the works, and a hard sintered surface is the least forgiving of a tight internal corner, so one is always cut with a generous radius. Internal corners are cut with a radius because square ones crack.

Bollards, planters and a one-way service road can turn what looks like a ten-metre carry into a fifty-metre one. Where a seam becomes unavoidable the choice of stone starts to matter, because a fine even speckle closes a joint almost invisibly and a broad vein simply will not. Yield drops the moment the building dictates awkward lengths. On a street with no restrictions the constraint is other residents rather than a warden, so it is worth putting a cone or a car out early. A granite kitchen ends its day with a sealer, and a sealer wants a dry face and a quiet hour afterwards, so that hour is written into the day rather than borrowed from it. A sealer needs a dry face and a quiet hour after it.

Honestly, no, though it would be easy to claim otherwise. What the research on this patch actually lists is worktop replacement and worktop splashbacks & upstands. That says something about the housing round here, not about the work. Quote, cut and fit are the same here as on any other part of the patch. Where kitchens turn over between tenancies the priority is a surface that survives a decade of being treated as a chopping board. Where several kitchens are ordered together the sensible move is to take them all off one batch, because two slabs of the same name bought six months apart will not sit happily in the same building. A focal surface deserves to be seen at full size. Landlord work is scheduled around void periods, so the whole thing is a fixed window and the template date matters as much as the fitting date. Volume work tends to live at the entry end of the range, and the entry end is genuine stone rather than a compromise, since the lowest supply figure we quote is a sintered surface and not a thin laminate pretending to be one. Specify before the room is finished, not afterwards.

Power and waste come up through the floor, and where they surface decides which cabinet can hold a sink and which one cannot. A shape like that nests kindly on a slab, so more of what gets bought ends up on the units and the rate per square metre behaves much as the brochure says it will. A pale honed face earns its keep in a room short of daylight. Material runs £110 to £550 per square metre supply only, and templating, fabrication and fitting each get their own line.

The returns into a breast recess are the tightest scribes in the room, and they are eased in rather than forced. A hob dropped into the middle of a length puts sustained warmth at the lip of a cut-out, and an engineered surface will yellow there across ten years where a natural one takes it without comment. An engineered surface yellows under standing warmth; natural stone does not. Send the run lengths, say where the sink and hob will sit, and tell us which way the room faces and what lighting is going in above the working run. Some doors in a building need a consent letter and some need nothing at all, so the first question is which arrangement applies here rather than which one is usual. That changes which questions are worth asking about the stone, because somebody staying put wants to know how a honed face marks in five years and somebody selling wants to know how it photographs next spring. The maintenance budget and the household budget buy differently.

An island is where this usually shows, standing free with no wall to level against. Variation past what packing can take up has to be corrected in the carcasses before we cut, because the template records the units as they stand. Levelling belongs in the carcasses, on their own legs and packers. An alcove is commonly wider at the back than at the front, so a piece cut to the opening drops in and then stands off the rear wall. A run that sits under strong sun for hours every afternoon suits a surface built to be stable in daylight, because a resin-bound stone is made for indoor use and sustained sunlight is the one thing it was never designed around. Strong daylight is an argument for a surface built to take it.

There is nothing to pay before the template visit. The design and quotation visit comes first. It is free and carries no obligation. The template produces a drawing, and the workshop cuts to that drawing once you agree it. An under-stairs cupboard eats one end of most of these kitchens, and the run stops at a door that has to keep opening. Which stone belongs on top of all that is a separate question from the building itself, and it is the one with a figure attached, because supply alone runs from £110 to £550 per square metre before a single cut has been made. Porous or not porous is the fork in the road on day one.

The edge profile is its own line, so a shaped edge and a square one are two different figures. The quote is written from the template drawing. Before that it works from what you have described. Material is quoted supply only and templating, fabrication and fitting sit on their own lines, so it is visible which part is stone and which is labour. The face of a breast is rarely flat, and a top returning onto it picks up that bow across the last few hundred millimetres of its length. A deep scribe eats into the back of the piece, which is quietly important on a stone with directional figure, since the pattern moves backwards as that depth comes off. A deep scribe moves the pattern back along with the depth.

A join is glued and clamped flush on the day, so it is fixed rather than something to be undone. Each join is an item on the drawing, so the layout and the figure move together. A join cannot cross a cut-out, so a sink mid-run takes away the position you would have used. A hob cut-out and the floor penetration feeding it have to land over the same cabinet, and where they do not it is the stone that gets redrawn rather than the pipework. An island is the piece that decides whether one slab covers the kitchen or two, and a second slab arrives as a step in the figure rather than a gentle slope. The shape sets the cut list and the cut list sets the stone bill.