Worktops in Campden Hill

Yes. Campden Hill is on the patch, and the postcodes we work here are W8. It is worked on our west London run, along with the rest of Kensington and Chelsea. Where the van can pull up level with the gate the pieces are handled the fewest times, which is what actually protects them. Whatever the standing allows, the stone leaves that van finished, because every edge, cut-out and internal radius is machined at the works and none of it is open to reconsideration at the kerb. Pieces are unloaded in laying order so the figure runs true. You never have to visit anything or collect anything: we template in your kitchen and fit in your kitchen.

Walls are thick, lime-plastered and built in a soft brick, so they take a scribe well and take a fixing badly. The kitchen in one of these sits in the back addition and takes its daylight from one end, so the working half of the run is the darker half and a pale stone with a honed or matt face does more there than any colour with depth in it. The island earns the liveliest part of the stone. A cill projecting forward of the plaster line pushes the back edge out, and the units then stand off the wall by that amount for the whole length. Every notch and every scribe is machined into the piece before it leaves the works, and a hard sintered surface is the least forgiving of a tight internal corner, so one is always cut with a generous radius. Brittle stone and narrow returns are a poor pairing.

A short run of external steps before the communal door means a piece is lifted twice before the staircase proper has even started. That caps the longest piece, and a run split into two lengths nests differently on the slab, which moves the yield and moves the figure with it. The protective film peels off last so the finish is untouched. Unrestricted does not mean empty, and a street that is clear at seven is usually full by nine. A granite kitchen ends its day with a sealer, and a sealer wants a dry face and a quiet hour afterwards, so that hour is written into the day rather than borrowed from it. A reserved slab is a slab nobody else is allowed to buy.

Not really, and claiming otherwise would cost nothing and mean nothing. What the research on this patch actually lists is worktop fabrication and worktop installation. It reflects the local housing rather than any difference in the work. It is quoted, cut and fitted here the same way it is anywhere else on the patch. The junction between the original room and the extension is the point to watch, because the two floors rarely sit at the same height. Where several kitchens are ordered together the sensible move is to take them all off one batch, because two slabs of the same name bought six months apart will not sit happily in the same building. Heavy daily cooking is an argument for natural stone. Extension kitchens are usually specified long before they are buildable, so the run lengths on the drawing and the run lengths in the room are different numbers. Volume work tends to live at the entry end of the range, and the entry end is genuine stone rather than a compromise, since the lowest supply figure we quote is a sintered surface and not a thin laminate pretending to be one. A small kitchen still buys the remainder of the slab.

On a heavily veined stone the island and the run behind it are nested off the same area of slab so the movement relates across the room. A shape like that nests kindly on a slab, so more of what gets bought ends up on the units and the rate per square metre behaves much as the brochure says it will. Every return end is another polished face to pay for. Supply-only material is £110 to £550 per square metre, and templating, fabrication and fitting are quoted separately rather than rolled in.

Where the sill lands inside the height an upstand would occupy there is no upstand, and the stone either dies into the reveal or stops short of it. A hob dropped into the middle of a length puts sustained warmth at the lip of a cut-out, and an engineered surface will yellow there across ten years where a natural one takes it without comment. What the room obstructs, the layout pays for in slab. Send the run lengths, say where the sink and hob will sit, and tell us which way the room faces and what lighting is going in above the working run. Where ownership is split across a building, the common parts belong to someone else and the carry route is negotiated rather than assumed. That changes which questions are worth asking about the stone, because somebody staying put wants to know how a honed face marks in five years and somebody selling wants to know how it photographs next spring. Hard use by people who did not choose it points at sintered stone.

What comes out goes by the same route the new stone comes in by, which is why that route is walked before anything is lifted. Disposal means it goes in the van, not into the garden to wait for a collection. The units stay where they are and only the surface changes. A skip, a delivery lorry or a run of scaffolding takes the frontage the van needed, so the street is worth a look the day before rather than on the morning. Sintered surfaces are the hardest of the three to machine and the messiest to cut wet, which is precisely why none of that happens on a public pavement. Cutting is done wet and extracted, never dry on a pavement.

Small variation is taken up by packing under the top on the fitting day. Stone does not flex, so a run that rocks on its carcasses rocks just as badly once it is stone. If the carcasses are corrected, the template is taken again, since a drawing off units that then moved is worthless. Casement handles and stays swing down into the space above the worktop, so the clearance that counts is the one measured with the window open. A run that sits under strong sun for hours every afternoon suits a surface built to be stable in daylight, because a resin-bound stone is made for indoor use and sustained sunlight is the one thing it was never designed around. A cut-out beside a notch leaves very little stone in between.

If a piece cannot be got in at all, we say so at the template rather than on the day. The alternative to a join is a shorter run, which is usually the wrong thing to trade away. Splitting a run costs a join, and that is the price of getting stone into the room at all. The measurement that decides everything is the diagonal between the underside of the flight above and the outer edge of the turn below it. Where a seam becomes unavoidable the choice of stone starts to matter, because a fine even speckle closes a joint almost invisibly and a broad vein simply will not. A remnant worth keeping rides back on the van rather than to a skip.

Nothing is cut out in the kitchen. Cutting a bowl on site is how worktops get cracked. A Belfast or butler sink has to be installed and at its final height before the template, because the stone is cut to sit on it. A sit-on sink and an undermounted one are different cut-outs, so which it is gets settled before the template. Seating overhangs past roughly 300mm will not carry on the carcass alone, so flat steel bar or a plywood substrate has to be built into the units first. An island is the piece that decides whether one slab covers the kitchen or two, and a second slab arrives as a step in the figure rather than a gentle slope. The island is usually the piece that opens the second slab.